• Jeśli chcesz dodać swojej Alfie charakteru i jednocześnie zaznaczyć przynależność do naszej społeczności – to dobry moment, żeby je zamówić.

    Ramki Alfaholicy

    Szczegóły, zdjęcia oraz informacje o zamówieniu znajdziesz tutaj.

    Nie czekaj, bo jak zwykle schodzą szybko.

[Giulietta] Chiptuning.

Unfortunately for me, after visiting Cinek, the soft was done poorly. The car surged on a cold engine. He said it could be the EGR. The car was saved by FCA Bielsko by flashing a new soft. A bit shameful because he charged 1500 PLN... and he messed up my car!!
And were you at his place with a complaint?
 
Hmm, I also thought about removing the EGR by Cinek - maybe someone who had done it there (even just Cinek himself) can share information on how he does it in SW? Because I heard there are different methods - from careful remapping (or something like that) to removing half of the error code tables...?
 
I wrote to him whether it was the soft's fault because I still have the car under warranty and I need to know. He replied that it wasn't and the likely culprit could be the EGR. So he went to FCA Bielsko. They had the car for 3 days for tests but they arrived at the conclusion for which I commend them (I didn't tell them the chip had been done).
 
Did you measure power and torque before and after installing this soft from MM? I'm interested in specifics.

This isn’t soft. It’s an external controller with soft for a specific engine with optional additional corrections. The car wasn’t on a dyno. Closest I have to a 'Cinek' is one conversation on the phone, after which I was discouraged to visit him. "Master" of the world. I measured only 0-100 acceleration. Stock was 7.8–7.9, now it’s 6.9–7.0. However, I recommend the Jata service in Świdnica. I replaced the MA module there last week. Both the price for the module and the replacement were very reasonable, and the execution time was 2.5 hours.
 
On the Cinsoft Facebook page there is Alfa 1.4 MA 150 HP made to 186 HP, 272 Nm, program flashed via OBD2. Strange that Cinek didn’t propose reverting to the old program; that’s standard. He probably doesn’t release cars that aren’t working.

I have a 2.0 JTDm and not a 1.4 MA. After the dyno the car is warmed up. The problem was on a cold engine. I’ve had many cars after modifications, all done in dynosource, and never any problems.
 
Last edited:
Yes I know it was about the JTD; I wrote that in the event of problems the tuner should either prove it’s the EGR problem or simply revert to the old program and then check if the problem occurs. As far as I know Cinsoft guarantees you can revert to the old program if something is wrong. If the car was under warranty, the tuner should check the car before flashing new maps and cannot blame an EGR that wasn’t functioning. You should have pressed Cinek, unless he dodged you, which would reflect poorly on the tuner.
 
Gentlemen, I’m in the stage of gathering parts for a replacement in Giulietta 1.4 T-Jet 120 HP EURO5. As it turned out today, I have a damaged catalytic converter - it clatters when revving the engine. I will definitely need to replace it. And here the problems arise. Factory I have a catalytic converter with catalog number 51938292. I can’t find anything about that number anywhere except the new one for 4400 PLN :rolleyes: Therefore I need to look for another lifeline. Will another 1.4 T-Jet catalytic converter fit, or are there other catalog numbers, or will it start throwing a check engine? Is there only hacking, or DownPipe? Are there any alternatives? Will a MultiAir catalytic converter fit, or then only a new Garrett turbo + remap?
 
Every 1.4 t-jet will fit. In MA the mounting to the turbo is different.
 
I see relatively many used catalytic converters are from 500 / Abarth 1.4. Was IHI installed there, or Garrett? I found such a cat:
https://allegro.pl/oferta/katalizator-fiat-500-abarth-1-4-t-lift-50546951-8168646835

Will a catalytic converter fit my VL39 turbo? I see the seller also has a VL38 turbo, supposedly from the same car. Unfortunately in EPER there is silence regarding this catalog number. It doesn’t match any model :( https://allegro.pl/oferta/turbosprezarka-fiat-500-abarth-1-4-t-jet-55248311-8168868157

Hmm... And what if you take the catalytic converter and the turbo from this seller, would there be any power increase? VL38 probably has greater potential than VL39
 
Last edited:
It’s better to go Garrett plus cat from MA
 
It is known that then you can count on a greater power increase. I don’t, however, care about extremes, and with VL38 it seems to be plug-and-play and you can reach ~160HP — perfect for me. Moreover, the catalytic converter to a 1.4 T-Jet EURO5/6 is hard, and MA I won’t even mention — on Allegro one unit in an unspecified condition.

The question is only whether I would have to do the program right away, or can I wait a bit with it? Appointments are probably difficult from day to day :(

@ ahaa, when mounting a catalytic converter from the EURO6 version to my Giulietta EURO5 will I not make a "mess" ?
 
Last edited:
I don’t, however, care about extremes, and with VL38 it seems to be plug-and-play and you can reach ~160HP

That’s likely an extreme
A cat like a cat should fit and I don’t think there will be a difference in construction.
If your ECU won’t report errors after installing the Garrett, then probably some time of easy driving won’t hurt the engine.
 
Last edited:
Now I will definitely have to replace the turbo. A photo just sent by the mechanic:


Gentlemen, what could have happened?! I’m terrified by this view.
Replacing the turbo is a piece of cake, but somewhere there must be the cause of such rotor damage... :sad:
 
A mate who handles the car said it looks like something got in. But from the exhaust side? How could something end up there? He said it looks like each blade had a loss of about 10-15%.
Valve timing is correct, so the ignition angle shouldn’t pose problems. Apparently clearances on the rotors are also imperceptible.

Best of all I didn’t notice symptoms indicating turbo malfunction — power is there, turbo was charging ok.
 
Then a camera and a piston inspection if they are intact.
 
Today will be the search for the culprit of this whole mess. I would prefer not to find that something flew from the engine. I already have enough good news.

If the powertrain is OK, I’ll still be buying bigger things. Slowly putting everything together:
I’m thinking about a VL38 55248311 turbo kit + 2.0 JTD intercooler. Once I somewhat climb back from financial bottom, Cinsof car program. Mainly to lower EGT.
Am I understanding this right / am I thinking correctly, or is there something else worth doing?
 
Half a year ago I’d have installed Garrett without hesitation, but Julka has exhausted me too much lately. I’ll drive it for maybe a year, max 2, and we’ll go for a bigger sister (Giulia) to the showroom ;)
I don’t need a spectacular power increase to carve more aggressively. And since I want turbo, I have to replace it, I came up with an idea for one with a bit more potential.

Question is whether it will work as intended, or perhaps I’ll end up carving an even bigger problem with tuning this exotic setup :rolleyes:
 

Related threads

Amortyzatory
Back
Top