• Jeśli chcesz dodać swojej Alfie charakteru i jednocześnie zaznaczyć przynależność do naszej społeczności – to dobry moment, żeby je zamówić.

    Ramki Alfaholicy

    Szczegóły, zdjęcia oraz informacje o zamówieniu znajdziesz tutaj.

    Nie czekaj, bo jak zwykle schodzą szybko.

[Giulietta] Chiptuning.

Ask Cinsoft :)

I think in the original post you meant to say you have a 2.0 with GTB14. Because if you already have GTB15 then yes - another GTB15 will fit.


Yes I have GTB14, the question is whether a plug and play GTB15 will fit
 
We’re only talking about probably the second generation of Multiair. There may be differences between generations; inside, probably not. T-jet operates on a completely different principle and there different cams have their place. It’s also strange that up to 4500 rpm 150 and 170 have identical parameters, characteristics, which results in the same volumetric efficiency; with other cams that would be unattainable.

Sent from my URSUS C-360 3P

In these cams, there isn’t such a big difference that the bottom is worse, and the top provides better flow.
 
Last edited:
Uncle Eper talks about a common cam for 110 and 125 kW.
Turbo is the same, the cam is the same, only modified to about 200 HP
 
Uncle Eper talks about a common cam for 110 and 125 kW.
Turbo is the same, the cam is the same, only modified to about 200 HP
Exactly. The problem is that as I said, I talked to Cinsoft and Conmир and they’re not able to pull as much from 150 as from 170 and they don’t know why. Conmir wrote that he never analyzed the cause.
 
Once my warranty runs out, I’ll try it myself.
We’ll see what comes of it.

Sent from my URSUSa C-360 3P
 
I got a quote from Cinsoft. Damn, should have bought the 1.4 MA :rolleyes:

If target around 170hp and 250Nm:
- new turbo with the Tjet 150 about 2250 PLN gross
- turbo removal/installation 400 PLN net
- usual items needed for replacement (oil, filters, gaskets etc) about 400 PLN gross
- more powerful intercooler about 1300 with installation
- tuning for the vehicle 1300 net
 
Over 5000 zł. I’m thinking about it too, but that’s a lot for a whim.
 
Exactly. The problem is, like I wrote, I talked to Cinsoft and Conmire and they can’t pull as much from 150 as from 170 and they don’t know why. Conmir wrote that he never analyzed the cause.

Maybe these 'tuners' don’t really understand what the engine control unit does. They flash maps available on portals (and there are such), and then make minor adjustments.
I still support this http://www.me100t.com/me100t/?page_id=361
You have MM soft and zero problems.
I have it on my car and it’s great. And I have no relation to MM.

- - - Updated - - -

Exactly. The problem is, like I wrote, I talked to Cinsoft and Conmire and they can’t pull as much from 150 as from 170 and they don’t know why. Conmir wrote that he never analyzed the cause.

Maybe these 'tuners' don’t really understand what the engine controller does. They flash base maps available on portals (and there are such), and then make minor adjustments.
I still support this http://www.me100t.com/me100t/?page_id=361
You have MM soft and zero problems.
I have it on my car and it’s great. And I have no relation to MM.
 
Did you measure power and torque before and after installing this MM software? Concrete data interests me.
 
Maybe these 'tuners' don’t really understand what the engine controller does. They flash base maps available on portals (and there are such), and then make minor adjustments.
These 'tuners', as you call them, probably know what they’re doing and simply don’t want to ruin someone’s engine to gain a few horsepower.
And the MM ECU is known for being stubborn to tune.
 
Is it factory? Or did Cinek modify something?
 
This is great for owners of such versions
 
Unfortunately for me after visiting Cinek, the software was badly done. The car stalled when cold. He said it could be the EGR. The car was saved by FCA Bielsko by uploading a new software. A bit embarrassing because he charged 1500 PLN... and ruined my car!!
 
On Cinsoft's Facebook page there is Alfa 1.4 MA 150 HP tuned to 186 HP, 272 Nm software uploaded via OBD2. Strangely, Cinek did not propose returning to the old program; that’s standard. He probably doesn’t release cars that aren’t working.
 
Good that you’re writing this. Great advertisement for Cinsoft. Maybe someone here should comment on this? I also wanted to chip there, but if it looks like that, thank you.
 
Amortyzatory
Back
Top