• Jeśli chcesz dodać swojej Alfie charakteru i jednocześnie zaznaczyć przynależność do naszej społeczności – to dobry moment, żeby je zamówić.

    Ramki Alfaholicy

    Szczegóły, zdjęcia oraz informacje o zamówieniu znajdziesz tutaj.

    Nie czekaj, bo jak zwykle schodzą szybko.

Engine splash shield

Does anyone use such an aluminum shield? I’m also wondering about it.

Could someone quote the thread why using such a shield could trigger airbags? Is it in case the underbody hits an obstacle?
 
To use such a shield you need to use rubber spacers (standoffs) between the body and the shield. A shield screwed rigidly to the body "acts" as part of the body. I had such a case, shield screwed rigidly, hit a small stone and the tensioners fired. The airbags did not deploy. At the ASC they wondered how it happened for a long time. From Italy came the answer that the tensioner sensors respond to the frequency of vibrations that occur during a collision and airbags did not deploy because they did not receive the correct signal..
 
I ordered a Polcar one, we'll see what it’s good for and whether it even fits...
I’d rather not check the original in the ASC ;)
 
I bought this one for up to 100 PLN on Allegro; sure, guys said it’s too short and too narrow, true, but it could be modified by welding nuts to the brackets and bolts with large washers, I drilled the holes in the shield to fit; the front part lines up with the bumper. To even remove the old original I had to cut up all mounts. I had damaged it. I even transferred that metal shield under the exhaust from the original. Not possible? I called the company that makes it and reported it didn’t fit; they were surprised. Circus
 
Can someone say something concrete about the shield from POLCAR? I heard most holes need modification, but that's probably not a big problem. More about the shield dimensions themselves - length, width. How about durability? And finally maybe a silly question, but what does lack of this thermal shield cause?
 
Gentlemen, and I have a question in this topic whether you can drive without a shield? The mechanic recently removed it (or what remains of it) and I don’t know whether to look for another unit or not rush with this..
 
I echo the question - what are the consequences of driving without the shield besides dirtying the engine? I don’t intend to practice this long-term, but for the next few weekends I’ll need to peek at the AR from underneath, and I don’t want to remove the shield each time.
 
water may get into the air filter
I think not.

I have a second car on which I did 250,000 km across Poland and still without a shield. The car still runs today and hasn’t had any engine/gear issues. Even the alternator and starter are original. The only problem is that whatever I touch under the hood gets covered with a thick layer of dust/dirt.
 
Is the engine cover the same in every 159, or does it depend on the engine installed in the car?
 
Hello. Reviving the topic. I'm considering buying an engine cover for Brera 2.0 jtdm; in my current 159 I don't have the original (that was already installed) and nothing much happens, i.e., it hasn't deformed under heat and I’ve driven for over three years. I’ve gone through your posts, rummaged on Allegro, and I’ll probably choose a cover made from pure PCV (as long as not polyethylene - they reportedly deform over time). However I noticed used original covers have insulation. Does anyone know if that actually provides any benefit compared to, say, a non-original housing? Specifically, does the car actually become quieter or is it negligible? I’m talking about diesels because they clatter a bit :) Maybe someone here tested this, e.g., replaced the non-original housing with an original. P.S. Two identical engines with similar mileage, one with a non-original, the other completely without a cover — the difference is really noticeable.
 
Gentlemen, does anyone have a lead on a tested engine cover for Jtdm? One that doesn’t require modifications? I went to the dealership and they quoted 850 zł :-D I’d rather keep it under 500 zł. I don’t want junk from Allegro, just something proven and reliable. Thanks in advance for any reply ;-) Best regards
 
Amortyzatory
Back
Top