• Jeśli chcesz dodać swojej Alfie charakteru i jednocześnie zaznaczyć przynależność do naszej społeczności – to dobry moment, żeby je zamówić.

    Ramki Alfaholicy

    Szczegóły, zdjęcia oraz informacje o zamówieniu znajdziesz tutaj.

    Nie czekaj, bo jak zwykle schodzą szybko.

Engine splash shield

Thanks Greciu!!!! Engine cover ordered :-D with shipping 615 zł. just for future readers.
 
Hi Guys, Could someone tell me if such a cover (diesel version) will fit my car so I can transport it? I have a SW :) because I’m not sure whether to order online or better to go to the nearest dealer and replace during the next oil change...
 
Hello I recently mounted an aluminum engine cover for my Alfa, like this one
http://allegro.pl/oslona-pod-silnik-aluminiowa-alfa-romeo-159-brera-i5893675659.html
fits without a problem including the mounting holes; the only thing I had to do was to crease it a bit because after installation the braided exhaust shield rested on the cover and I was afraid it would rattle. And you could possibly bend it slightly to sit perfectly at the front; I left it to allow some air to enter for engine cooling.
 
And where did I read that those mounts blew when such a plate was hit
 
ciusiek - you must very carefully make the insulation of the cover and the body (rubber spacers), mine blew the seatbelt pretensioners.
 
Marek 156/159sw could you clarify what you mean by insulation of the cover and its relation to the belting pretensioners going off because I don’t really get it. I know the cover with rubber on the engine side can be bought, but after talking to the manufacturer I gave up because I didn’t see any sense, as the manufacturer confirmed (this option was introduced because some earlier customer insisted on it, arguing it would better dampen the resonance from the engine with the cover installed)
 
It’s about the aluminum plate potentially resonating or striking an uneven surface causing a signal to the impact sensor. The consequence for the colleague was the airbags deploying. In my opinion too big a risk because instead of belts airbags could deploy. But you don’t have to listen to me; I’m just following logic and a forum post
 
I described the matter earlier as a warning. I installed an aluminum engine cover, bought at an 'Alfa Shop'. Everything was fine until I scraped the cover on a pothole. Vibrations caused the belt tensioners to fire (an interesting experience). After that, specialists took a long time to figure out how it could happen (tensioners fired but the airbags didn’t). It turned out the sensor that triggers the tensioners worked correctly by 'reading' the frequency of the bent sheet, while the airbags’ sensors didn’t have any signal. To avoid a similar situation, specialists advised using the factory cover or, not taking responsibility, to isolate the cover from body components with rubber spacers (isolation). That isolation helped, and it worked, because other times when I grazed a protruding rock nothing happened, despite similar noise and marks of abrasion.
 
To clarify: the airbag control unit has two triggering programs: 1. only pretensioners, 2. pretensioners and airbags. The programs are adjusted to the type of collision. And that hard impact on the cover was enough to trigger program 1
 
jaboleq you’re probably right about the basic function of the engine cover, but my Alfa was modified by the previous owner which lowered it (in Germany that may not matter given road quality). For our roads, where the condition isn’t European-level, I decided the cover should also protect elements like the exhaust wrap which in my case was already slightly moved. It’s not about turning my car into a snowplow but so that some stone wouldn’t tear off the wrap. I’m surprised that a stone hitting the floor (under the car) would trigger belt pretensioners; I thought sensors were placed at the front sides and hits there would cause sensor activation.

- - - Updated - - -

yes I could mount the original plastic cover, but it would hurt if that stone damaged the freshly fitted cover for only 260 zł and this is a used part from Allegro.
 
That stone must have been really big, and in case of damage you have to report it. In a normal country you’d get your money back easily; here in Poland it’s a uphill battle.
 
That stone must have been really big, and in case of damage you have to report it. In a normal country you’d easily get your money back; only in Poland it’s always uphill.

Ha, I can already see how the Municipal Road Authority would pay out compensation. First they’d say the reason was non-original cover installation and then that excessive speed.
 
If you hit it, it will be the same whether it’s aluminum or plastic. People here say with a sport suspension and low profile tires they don’t install such things. For your safety and others don’t install it; you have a live example.
 
Hello, Could you advise me :) I bought an Alfa a year ago that didn’t have an engine cover. Besides engine protection, does it dampen the incredible JTDm rattle you can hear very from outside? (inside I have no complaints) I’d like to buy such a cover. Do you recommend anything?
 
Amortyzatory
Back
Top