• Jeśli chcesz dodać swojej Alfie charakteru i jednocześnie zaznaczyć przynależność do naszej społeczności – to dobry moment, żeby je zamówić.

    Ramki Alfaholicy

    Szczegóły, zdjęcia oraz informacje o zamówieniu znajdziesz tutaj.

    Nie czekaj, bo jak zwykle schodzą szybko.

Engine splash shield

Drone

New
Joined
Feb 15, 2011
Messages
58
Location
Warszawa
Car
Mitsubishi Lancer
Is the engine undertray the same on every 159, or does it depend on the engine installed in the car?
 
When I was buying one for mine on Allegro, the seller said they’re all the same and it really is like the original and fits.
 
When I was buying one for mine on Allegro, the seller said they’re all the same and it really is like the original and fits.

It could be as you say, but you have a 1.9 petrol, so surely any cover will fit. I have a 2.4, the oil pan is low and I’m not sure if for that engine you need a different cover to buy :(
 
That’s why I wrote that he didn’t even ask me what engine, because he said it’s the same for all; for certainty you’d have to check in ePer, whether they have different numbers, although even that won’t be 100% proof that they don’t fit, but if they’re the same, then everything will be known - I’ll try to check now.

There are a few numbers in ePer, so there’s no 100% certainty - best to find one on Allegro and ask the seller for the one specific to you.
 
Last edited:
There’s a difference between the 1.7 TBI petrol and the 1.9 and 2.4 diesels (diesels are the same) so here it matters only whether it’s a diesel or petrol; I bought recently and it says Alfa 1.9 2.4 and that’s it.
 
Does anyone know how to remove this cover? These pins turn in place, and I need to replace it because my old one is broken
 
and that’s the pain when changing the oil one of them was turning but I moved the plastic and it popped out. I think you could MIG-weld the element that the screw threads into to the frame, then the screw would loosen
 
Does anyone know how to remove this cover? These pins turn in place, and I need to replace it because my old one is broken

These aren’t pins but screws screwed into rivet nut fittings.
I used a sheet-metal clamp (the largest - the one with long arms - like in the photos from this auction: http://moto.allegro.pl/33836-scisk-blacharski-szczypce-samozaciskowe-i2286210794.html), which I filed down appropriately so I could push it under the cover and clamp on the rivet nut flange, after removing the cover I reinforced the rivet nuts (the ones that loosened) - re-crimping them with a rivet tool for rivet nuts.
 
There’s a difference between the 1.7 TBI petrol and the 1.9 and 2.4 diesels (diesels are the same) so here it matters only whether it’s a diesel or petrol; I bought recently and it says Alfa 1.9 2.4 and that’s it.

OK, I bought a used original on Allegro. It said diesel ;)
 
In three weeks I’ll be in Łódź and it’s probably worth buying a cover that I don’t have. What discount can I count on? :P
Buying it is easy, but you also have to install it, not really doable without a lift or pit, and I’d like it done properly.
 
I bought a used engine cover from a scrapyard on Alledrogo, in very good condition.
Originals include a heat shield, which is missing in cheaper versions. I worried about durability of cheap plastics and their heat resistance. I removed the old cover myself, left the car to a workshop for mounting due to some broken mounts/screws. I paid 40 PLN and it’s like new.
 
how much did you pay?? I paid 100 PLN and the cover is well made :)

I paid, if I remember, about 140 PLN. I’m too lazy to check the history on Allegro :D
I know new replacements were cheaper, but I read many bad things about replacements for this part. Specifically about the material they’re made from, i.e., ABS.
It’s not a very durable material, it cracks easily on impact. If the plate is made from this material, the protection will be much weaker than the original.
If someone on the forum bought a toilet seat made of that material :D, you know what I mean ;) (a light joke, but I actually had such a seat and know the difference between ABS and non-ABS seats)
 
Finally, I’ll add that this cover fits the 2.4
If it says “for diesel” there’s no problem and it will fit :)
The car outside became twice as quiet, and inside it’s nicer too :)
 
These aren’t pins but screws screwed into rivet nut fittings.
I used a sheet-metal clamp (the largest - the one with long arms - like in the photos from this auction: http://moto.allegro.pl/33836-scisk-blacharski-szczypce-samozaciskowe-i2286210794.html), which I filed down appropriately so I could push it under the cover and clamp on the rivet nut flange, after removing the cover I reinforced the rivet nuts (the ones that loosened) - re-crimping them with a rivet tool for rivet nuts.

Or do you remember what thread the rivet nuts have, because at the last oil change I stripped one screw, it rotated. I’d be grateful, because I don’t want to lie under the car to undo one and check myself.
 
It serves several functions, among others it quiets the engine, protects the bottom from damage, but mainly prevents the engine from getting dirty and, for example, flooding the electricals and electronics. I don’t know how it is in the 159, but absence of the cover in the 146 + dynamic drive through a puddle could cause the alternator housing to crack.
 
not to install a new hood, again about the lower cover.
Some time ago, as a precaution, I bought a used lower engine cover. It looks great, all mounts, but there’s one catch.
Instead of a heat-resistant coating (aluminium??), there’s some kind of sponge stuck on the cover. What is this sponge, did they always use such things? I admit that when I broke the original, there wasn’t such sponge, only a strip, probably aluminium. Can you install such a cover with sponge on it without issues?
 
Amortyzatory
Back
Top