• Jeśli chcesz dodać swojej Alfie charakteru i jednocześnie zaznaczyć przynależność do naszej społeczności – to dobry moment, żeby je zamówić.

    Ramki Alfaholicy

    Szczegóły, zdjęcia oraz informacje o zamówieniu znajdziesz tutaj.

    Nie czekaj, bo jak zwykle schodzą szybko.

Engine splash shield

Looks nice... Is that metal? Have you heard about airbags going off after installing such a plate and in a minor collision? I read something like that on the net once, but I’m not sure how true it is...

For me the tensioners fired after hitting a stone. The shield was aluminum (bought in Germany). After about 8 months it was recalled. After long investigation it turned out the plate must be very well insulated from the body, and that even this is not a guarantee that vibrations (the frequency caused by impact) won’t transfer to the body, which would trigger the tensioner sensor and possibly the airbags. None of the tuning firms I know make aluminum or even steel shields for the civilian versions.
 
I paid about 500 PLN including installation.
I haven’t encountered such an opinion, but considering the road I drive home on I really have no choice (the standard shield didn’t last long) - I’ve bumped into it many times with the shield on and so far nothing happened.
In my previous car I also had such a plate installed and nothing happened either.
Maybe I’m just lucky :)
 
Last edited:
I paid about 500 PLN including installation.
I haven’t encountered such an opinion, but considering the road I drive home on I really have no choice (the standard shield didn’t last long) - I’ve bumped into it many times with the shield on and so far nothing happened.
In my previous car I also had such a plate installed and nothing happened either.
Maybe I’m just lucky :)
Have you thought about changing to higher-profile tires? The engine shield isn’t meant for mechanical protection.
 
I was thinking, but on these Alfas it looks better :) Actually, most of the time I just lightly scrape the underside because for now there is still a dirt road and it will probably stay like that for a long time. The factory shield cracked, so I replaced it with this one and so far I have no problems and I hope it stays that way.
 
The beam is a rectangular profile. I don’t know exactly how thick the wall is but surely not more than 3 mm. Drill out the old screws and old rivet nuts, measure the hole diameter ->http://carbonsteel.pl/wp-content/uploads/sites/3/2015/03/nitonakretka-2.jpg (standard screws are M6 so probably diameter 9). If it’s at a small plus 9 i.e. from 9.1-9.2 you can press in the same rivet nut for M6 when the hole widened more then drill to fi11 (for M8 screw) rivet (inserting rivet nut to thickness 2-3mm) or measure wall thickness and choose appropriately) you can riveting with a riveter like in the link or manually e.g. for rivet nuts from M3-M6 -> http://srnarzedzia.pl/pol_pl_Nitownica-do-nitonakretek-417_1.jpg or from M8 upwards ->http://norsteel.pl/wp-content/uploads/2014/09/PNT210-1.png. Small note with manual riveters (and surely with M6) you don’t buy stainless rivet nuts because you can’t squeeze them.
And should these nutserts be steel, aluminum, galvanized?
 
The best would be from acid-resistant steel or stainless steel; if they are galvanized then also okay, just acid-resistant as I mentioned earlier cannot be crimped with a manual rivet gun
 
I'm also curious how it behaves in use, supposedly made of HDPE... My Alf needs replacement too, after the last impact with a stump at night ;( I even wrote to the guy, he replied that it's not too short and the holes don’t sit perfectly but there are beans and you can adjust

I’m curious how it will sit, my shield is a bit patched up and I’d like to replace it but I’m not sure it’s worth a replacement.
If you decide, let me know how the installation goes and the result! :)
 
Hello
Can you buy an original mounting kit for the shield somewhere besides the official dealer? There’s some set on Allegro but I can’t post the link.

Cheers
 
So how is the mounting with the screws? I mean the screws, does anyone know if the screws are the same regardless of version?? I have a 2.2 JTS; according to ePer I need 10x46835178 and 3x15534977. The problem is that 46835178 isn’t available apparently and Fiat Auto Parts says it was replaced with 51810312. These, in turn, cost 20.79 PLN each (i.e., 200 for the screws) :) if it turns out 51810312 doesn’t fit me I’ll be 200 lighter... I got lost in this ePer, does anyone know exactly how the shield is fastened?
 
Yes, you can do it much cheaper than 200zł but I’ll message you privately tonight
 
Guys, can the lower shields for 1.9 / 2.0 / 2.4 be interchangeable? I see my 2.0 differs a bit visually from those on auction listings, but the mounting hole pattern looks similar. I don’t want to waste money and would rather ask. Could someone confirm?
 
Does anyone know if these shields from all have oil drain holes? I'm talking about a 1.8. previously I had some non-original shield and the drain didn’t fit - only a jigsaw fixed that defect. Recently I hit some fastening straps with clamps and the shield cracked, so I’m looking for something else that won’t require cutting.
 
Unpopular opinion from a foreign channel related to Alfa Romeo motoring - this engine shield can collect water, causing the ski supports to rot in several critical spots. Remove it and don’t worry about it.
 
Amortyzatory
Back
Top