• Jeśli chcesz dodać swojej Alfie charakteru i jednocześnie zaznaczyć przynależność do naszej społeczności – to dobry moment, żeby je zamówić.

    Ramki Alfaholicy

    Szczegóły, zdjęcia oraz informacje o zamówieniu znajdziesz tutaj.

    Nie czekaj, bo jak zwykle schodzą szybko.

Engine splash shield

Seriously? It seemed to me that such a shield should protect against water splashing from below.
Does anyone have similar experiences with water collection and rusting?

Was such a shield factory-installed on Alfas 159/Brera?
When I bought my Brera, there was no shield in it, but that could have been removed earlier.
 
The shield has channels and holes to drain water, so it’s unlikely water would stay on it - in my JTS, even when washing the engine, not a single drop of water stays on the shield because all water immediately runs under the car - as a curiosity - in the 146 with TS engine, if there was no shield, every dip into a puddle would crack the alternator housing, because water from under the wheel shoots straight into it - I can’t imagine driving without a shield.

Another curiosity - Opel Astra G with 1.7 DTI engine - the shield under the engine had some material, not exactly felt nor foam, which actually retained moisture and GM launched a service campaign to replace these faulty shields - that extra material was meant to additionally dampen the engine.
 
Last edited:
Seriously? It seemed to me that such a shield should protect against water splashing from below.
Does anyone have similar experiences with water collection and rusting?

Was such a shield factory-installed on Alfas 159/Brera?
When I bought my Brera, there was no shield in it, but that could have been removed earlier.

In the 159 there should be a shield from the factory.

As for the sledge runners (sanki), before mounting the shield check their condition, if needed clean and treat, perhaps wax inside, because with or without the shield, those runners will sooner or later start to rot.

Sent from my M2007J3SY using Tapatalka
 
I’ve seen those poor versions, with back pedaling rods, with manual air conditioning and without a display between the gauges and the shields were factory.
 
I heard about someone who, at every lot where new 159s stood, checked whether they had shields under the engines :)
 
Seriously? It seemed to me that such a shield should protect against water splashing from below.
Does anyone have similar experiences with water collection and rusting?

Was such a shield factory-installed on Alfas 159/Brera?
When I bought my Brera, there was no shield in it, but that could have been removed earlier.

The shield is very easy to damage. Especially on smaller wheels or the Ti version. I managed to lose 2 over 4 years. I tried to be careful :). I also ordered something similar from Allegro - not sure if the same, but price range similar.
 
I heard about someone who, at every lot where new 159s stood, checked whether they had shields under the engines :)
I haven’t heard of anyone like that, but I heard that ePER doesn’t have an option to omit this shield and about someone who can’t use it :)

Sent from my M2007J3SY using Tapatalka
 
Thanks for all the replies.
I plan to do underbody/runners maintenance in the coming months, fix the exhaust, and later install such a shield so it’s ready for autumn wet weather.
Last winter there were a few times with a lot of snow on the parking lot and the car plowed through, and I thought this is exactly the situation where such a shield could be damaged.
I have quite a low ground clearance. 18-inch wheels, 235/45 tires, but low springs.
 
I haven’t heard of anyone like that, but I heard that ePER doesn’t have an option to omit this shield and about someone who can’t use it :)

Sent from my M2007J3SY using Tapatalka
I also heard about one where someone checked all VIN numbers of the produced poor versions in ePer for their equipment with engine shields under the engine :)
 
I also heard about one where someone checked all VIN numbers of the produced poor versions in ePer for their equipment with engine shields under the engine :)
I’ve heard of someone who can’t use ePER, besides checking everything by VIN :)

Sent from my M2007J3SY using Tapatalka
 
And, I’ve heard of someone who can check in ePer if any AR model came out without an under-engine shield :)
 
Amortyzatory
Back
Top