• Jeśli chcesz dodać swojej Alfie charakteru i jednocześnie zaznaczyć przynależność do naszej społeczności – to dobry moment, żeby je zamówić.

    Ramki Alfaholicy

    Szczegóły, zdjęcia oraz informacje o zamówieniu znajdziesz tutaj.

    Nie czekaj, bo jak zwykle schodzą szybko.

[Giulietta] Chiptuning.

Therefore I ask a colleague who did the software, how it looks in terms of temperature. From experience I know that a bigger cooler does not always mean a bigger lag, and often after the program fitting a bigger one is almost a necessity. I installed a much larger intercooler into a Golf V GTI and I hardly noticed any difference in throttle response. And after its installation I managed to achieve 265 HP instead of 245 with just the software, no mechanical changes. I see that the IC for 2.0 JTDm isn’t that much bigger, so in my opinion the difference in throttle response will be hardly noticeable and after the program it may not be there at all. From a 2.0 JTDm it is 580 x 144 x 80 and from 1.4 630 x 100 x 64. So some small modification with screwing it in is probably. The question is whether the inlet/outlet pipe diameters are the same.
 
In my opinion it puffs up a bit with harsher driving, I’m also looking for an IC. Does anyone know what ICs fit the 1.4 MA in dimensions relative to the 1.8? Because from something I read it fits plug-and-play, you only need to replace the rubber elbows with those from the 1.8. So maybe instead of tinkering and looking for something tuning-related, swap to original. Especially since the price on fmic.pl seems suspicious, over 1000 for other models and 539 zł (550x180x65mm) for the Giulietta.

http://fmic.pl/390-alfa-romeo
 
Therefore I ask a colleague who did the software how it looks in terms of temperature. From experience I know that a bigger cooler does not always mean a bigger lag, and often after the program fitting a bigger one is almost a necessity. I installed a much larger intercooler into a Golf V GTI and I hardly noticed any difference in throttle response. And after its installation I managed to achieve 265 HP instead of 245 with just the software, no mechanical changes. I see that the IC for the 2.0 JTDm isn’t that much bigger, so in my opinion the difference in throttle response will be hardly noticeable and after the program it may not be there at all. From 2.0 JTDm it is 580 x 144 x 80 and from 1.4 630 x 100 x 64. So some small modification with screwing it in is probably. The question is whether the inlet/outlet pipe diameters are the same.

The front end is the same across all versions, so I wouldn’t expect a mounting modification, perhaps only with the pipes, but that can be checked in the EPER by comparing numbers, or by comparing used diesels and 1.4 on Allegro.

- - - Updated - - -

In my opinion it puffs up a bit with harsher driving, I’m also looking for an IC. Does anyone know what ICs in the 1.4 MA have in dimensions relative to the 1.8? Because from something I read it fits plug and play, you only need to replace the rubber elbows with those from the 1.8. So maybe instead of tinkering and looking for something tuning-related, swap to original. Especially since the price on fmic.pl seems suspicious, for other models over 1000 and for the Giulietta 539 zł (550x180x65mm)

http://fmic.pl/390-alfa-romeo

FMIC has a better construction, larger cooling surface at the same dimensions, so there is something to think about with an aggressive program
 
So maybe instead of tinkering and looking for something tuning-related, swap to original. Especially since the price on fmic.pl seems suspicious, for other models over 1000 and for the Giulietta 539 zł (550x180x65mm)

http://fmic.pl/390-alfa-romeo
well the price is tempting :) If the FMIC for this is really better, then the concept is probably good, especially for 1.4 MA and a program 200+ :)
 
Sowier says Mito The 155 HP squeezed out over 250 HP and still has room, but it was limited by the intercooler and brakes. So an FMIC and more efficient cooling and necessarily better brakes come into it, because after the third braking the discs start to skate.
 
Sowier says Mito The 155 HP squeezed out over 250 HP and still has room, but it was limited by the intercooler and brakes. So an FMIC and more efficient cooling and necessarily better brakes come into it, because after the third braking the discs start to skate.
It should be noted that Sowier achieved this among other things by changing the turbo ;)
 
Which does not change the fact that if he had a more efficient IC then 300 HP is within reach of his turbo; the same relationship holds with a smaller turbo ;)
 
I think the price of the kit from fmic.pl stems from the fact that in Alfa the IC is already installed at the front from the factory and to mount it you don’t need many hoses and elbows. In other cars the IC is often tucked, e.g., in the wheel arch, or between the radiator and the AC condenser. Then to do FMIC you need more hoses, elbows, clamps, etc., and that costs. In general these radiators from FMIC have a good reputation and apparently quite good flow. The price of the fmic.pl kit is better than a new OEM one, so there’s no point in tinkering because it might turn out that the IC from a QV or 2.0 would choke more than a bigger IC from FMIC :)
 
The price is definitely attractive! In this price range you can try to snag a used IC on Allegro, but indeed better a new fmic.pl – avoids the risk of buying scrap. I think that with 250 HP from the 1.4 MA it was also necessary to do the intake, which is, standardly, not very clever. In Julias the air intake is high under the hood, in the environment of hot cooling fluid hoses... (Of course besides other things, but we’re talking intakes). Recently I did temperature measurements of the air being drawn (among others) - outside air temperature - 21 C. During gentle driving the intake held about 35 C, but two steps (II->III->IV section, and again two times in a row) were enough to reach 56 C. Again - if I understand correctly this is the temperature BEFORE the IC? Does anyone know from which sensor the intake temperature is reported by the OBD?
 
I think that with 250 HP from the 1.4 MA it was also necessary to do the intake, which is, standardly, not very clever. In Julias the air intake is high under the hood, in the environment of hot cooling fluid hoses... (Of course besides other things, but we are talking about intakes).

With Sowier the intake is stock. He put a bigger turbo from some Volvo, it fit, from what he says practically plug-and-play.
 
I think the price of the kit from fmic.pl results from the fact that in the Alfa the IC already sits in front and to mount it you don't need many hoses and elbows. In other cars the IC is often tucked, e.g., in the wheel arch or between the radiator and the A/C cooler. Then to do an FMIC you need more hoses, elbows, brackets, etc., and that costs. In general, these intercoolers from fmic.pl have a good reputation and supposedly quite good flow. The price of the fmic.pl kit is better than a new OEM one, so probably no point to mess with it because it might turn out that the QV or 2.0 IC will choke more than a bigger IC from fmics :)

I don’t know if I’m thinking correctly, please correct me... FMIC has a better design, thus better cooling, but for higher power/turbo you need an IC with a larger volume, i.e. larger dimensions, not just one that cools better.

- - - Updated - - -

So the only modification is bigger turbo (and of course tuning)?

First he did the exhaust at full flow + a programmer. Then came bigger injectors. The next step would have been a hybrid, but the shell didn’t withstand and cracked in half, and not long ago he just installed a bigger turbo.
 
I don’t know if I’m thinking correctly, please correct me... FMIC has a better design, thus better cooling, but for higher power/turbine you need an IC with larger volume, i.e. larger dimensions, not one with better cooling.

I am not an expert but in my opinion power is affected by air temperature - that’s why an intercooler is used. Cooled air = higher density = more air-fuel mixture = more power. And about the FMIC as the name says (Front Mounted InterCooler) its main advantage is placement that allows very good air cooling. In a GTI I had a “couch” intercooler between the A/C radiator and the water radiator - so airflow was restricted but after switching to one with larger capacity and completely aluminum from Audi S3 (mounted identically in the couch) cooling improved significantly and you could push the turbo harder. Therefore in my view, a larger IC improves cooling and also it’s good if the core lamellae don’t impede airflow because that causes lag. People used to mount ICs from Iveco and it was a disaster. Now new cores of similar size don’t cause this effect. And another question about the exhaust in the 1.4 MA - the engine probably meets Euro 6 - that would mean the catalytic converter is quite restrictive. I wonder how much a decent 3-inch DP without cat or with a metal one for Euro 3 would yield.
 
And another question about the exhaust in the 1.4 MA - the engine probably meets Euro 6 - that would mean the catalytic converter is quite restrictive. I wonder how much a good 3-inch DP without cat or with some metal one for Euro 3 would yield.

I have info from one Warsaw-based company. They proposed changing the intake (aluminum, but without changing the IC), a DP with their cat and then a custom setup with an酸 (acid) and of course tuning - all for about 215-225 HP (that’s what they did for the MiTo). Apparently the limiting factor is at intake temperature, and it’s worth considering a better FMIC. But the price exceeded my expectations. If I added changing the IC, easily 10k would pop. Thanks, that’s how much I could pay at the showroom and still have a QV. :D PS: I looked at the intake and the ePER - I think the temperature sensor is already in the intake manifold. It has number 77366837. Because what sits earlier on the IC->manifold pipe is a pressure sensor. That’s good news, you can easily study IC performance.
 
Last edited:
interesting what diameter the exhaust is in the 1.4. Up to 230 HP a 55mm pipe is enough - and I think surely not less. In my view, it would be enough to do just the DP - instead of the cat, which can be done for 500-600 zlotys + about 400 zlotys for a metal cat suitable for Euro 3. Then FMIC from fmic.pl for about 550 + tuning and there’s no way around ~220 HP not exploding.
 
I’m not sure I understood the costs you wrote - I saw offers for DP with a high-flow cat for 2.5k (artisan) - 4k (brand, imported). Unless a 3-inch straight pipe without a cat... That would be cool ;) My tuning plan for the 1.4 MA looks like this: ok, about 195-200 HP - do a program, insulate intake and DP with tape, ignore the rest. ok, about 215-220 HP - as above plus DP with a loose cat + more free-flowing exhaust (not QV, but custom). ok, about 230 HP - as above plus final cooling solution for the intake with a better IC - note that a more efficient IC is not needed for a sudden power increase, but for maintaining it in real road conditions. Above that I suspect bigger injectors, bigger turbo, standard. On the other hand, I wouldn’t go that far with the 1.4 MA, better to take a QV... If modifying, go for the strongest versions. Also (whether tinkered or not) I think the intake issue in Julkas is poorly solved. In MiTo it's different. In Julkas the plenum is next to the expansion tank, the IC->manifold pipe runs right next to the DP, overall not good. If you nudge Julka a bit, even without changing the software, it spews out from under the hood so you have to be careful about burns. Under the hood there’s a hell, I wouldn’t be surprised if it's 60-70 degrees in the intake, under heavier throttle.
 
And how does it look with intake temperature after the software? i.e., on hot days like we had recently does the car puff up faster during aggressive driving? because I’m also going to do a program but I’m wondering if I shouldn’t start with a decent FMIC. The stock one visible through the bumper seems small. Does anyone know if the QV had a bigger IC and if it fits the 1.4 with P&P or if you need to buy a set from fmic.pl?

I didn’t notice any puffing during spirited driving. Everything’s ok.
 
So you’re saying that in the Julia 2.0 JTDM there is a bigger intercooler than in the QV?? Is this a possibility when replacing :)
 
I’m not sure I understood the costs you wrote - I saw offers for DP with high-flow cat for 2.5k (artisan) - 4k (brand, imported). Unless a 3-inch straight pipe without cat... That would be cool ;)

A Magnaflow metal catalyst for Euro 2-3 you can buy online for about 400zł. Metal catalysts that support > Euro 4 I don’t think anyone still makes. About DP for example for my GTI I did in El-tec a 3-inch DP for 800zł + heat-wrap 300zł but that was years ago. For the Saab SS 2.0T I had before alfa I did it in Legionowo with a guy for 500zł a 2.5-inch. Generally, if you look around you can do it cheap. Especially since in Julka you only need to do the first short section - the connection to the rest of the exhaust is right after the catalytic converter. So for 3 pipes and 2 elbows, 2.5k is a gross overprice and that price is probably at MGmotorsport :) If someone had the first part of the exhaust machined with the catalyst, I could go around and ask for prices maybe with a group purchase. On a4-club a guy does a DP for about 350zł, 2.75'' and they scoop them up like fresh buns.
 
Amortyzatory
Back
Top