• Jeśli chcesz dodać swojej Alfie charakteru i jednocześnie zaznaczyć przynależność do naszej społeczności – to dobry moment, żeby je zamówić.

    Ramki Alfaholicy

    Szczegóły, zdjęcia oraz informacje o zamówieniu znajdziesz tutaj.

    Nie czekaj, bo jak zwykle schodzą szybko.

error during PROXI alignment

Of course the full version?
I would try another interface as well.
 
Of course. I bought a cheap elm from Allegro and it didn’t work at all. Now I have an elm-to-usb from Viaken so probably good hardware. I don’t know if previously in my Alfa there was a radio with nav and now it is standard. That's what the seller told me why the gauge flashes. Earlier it didn't bother me, but gradually I want to bring the Alfa to perfection
 
If the devices in the car were replaced you need to reflect that in the configuration. I assume there was Navi, and now you have a standard radio?
If so, first:
Can Setup / Proxi Alignment Procedure -> Regulation tab -> the displayed information: do you have None? If not, change it to None (if you have only radio, without B&M - if not, adjust).
Are the steering wheel buttons still there? If yes, it should be Type D/159 in the appropriate option. Otherwise: Absent.
Also review other options to match the actual state, e.g., vehicle type, display type, audio I/O... If the devices and wiring in the car are functional, with correct configuration the proxi should succeed (assuming the interface and program work ok).
 
Of course. I bought a cheap elm from Allegro and it didn’t work at all. Now I have an elm-to-usb from Viaken so probably good hardware. I don’t know if previously in my Alfa there was a radio with nav and now it is standard. That's what the seller told me why the gauge flashes. Earlier it didn't bother me, but gradually I want to bring the Alfa to perfection

And when you ordered the ELm from Viaken did you specify that it should be for an Alfa/Fiat? If not, there may be a resistor that is used by most cars, but in the Fiat group it should not be there. You can measure between pins 6 and 14 with a multimeter; if you get around 100–120 ohms you need to open the interface and remove that resistor.

The rest is to apply the advice from t0m, Proxi will not work if you have the configuration set incorrectly according to what MES sees (it can be wrong, or some ECU not functioning).
 
When ordering the ELMy from Viaken did you specify that it has to be for an Alfa/Fiat?

Yes, an ELM for Alfa/Fiat.

the same error all the time:
screen.jpg

CAN INFO:
2017-02-03 17:38:42
CONNECTED TO:
Alfa Romeo 159 1.9 JTDm 8V
CAN Info
--------------------------------------------------------------

List of configured ECUs:
Body Computer (NBC): Present
Engine Control Unit (NCM): Present
Electric Power Steering (NGE): Absent
Instrument Cluster (NQS): Present
Steering Wheel Switch Node (NVO): Present
Radio / Navigation with Maps Node (NRR/RMN): Present
Braking System Node (NFR): Present
Info-Telematics / MS Convergence Node (NIT/NCV): Present
Driver Door Node (NPG): Present
Trunk Node (NVB): Present
Air Conditioning Node (NCL): Present
Automatic Transmission Node (NCA-NCR): Absent
Steering Angle Sensor Node (NAS) C-CAN: Present
Parking Brake Control Node (NPB): Absent
Roof Console Node (NIM): Absent
Lateral Tilt / Side Acceleration Node (NYL): Present
Adaptive Cruise Control Node (NAC): Absent
Passenger Door Node (NPP): Present
Driver Seat Node (NAG): Absent
Assistive Braking Node (NBA): Absent
Passive Entry: Present
Steering Lock Node (NBS): Present
Gear Shift Node (NSC): Absent
Passenger Seat Node (NAP): Absent
Parking Sensor Node (NSP): Absent
Engine Signals Node (NSM): Absent
Airbag Node (NAB): Present
Air Suspension Node (NMA): Absent
Roll/Incline Control Node (NPS): Absent
Adaptive Headlights Node (NFA): Absent
Driveline Control/HALF Node (HALF): Absent
:
ECUs that responded:
Body Computer (NBC): Active
Engine Control Unit (NCM): Active
Electric Power Steering (NGE): Not Active
Instrument Cluster (NQS): Active
Steering Wheel Switch Node (NVO): Active
Radio / Navigation with Maps Node (NRR/RMN): Active
Braking System Node (NFR): Active
Info-Telematics / MS Convergence Node (NIT/NCV): Active
Driver Door Node (NPG): Active
Trunk Node (NVB): Active
Air Conditioning Node (NCL): Active
Automatic Transmission Node (NCA-NCR): Not Active
Steering Angle Sensor Node (NAS) C-CAN: Active
Parking Brake Control Node (NPB): Not Active
Roof Console Node (NIM): Not Active
Lateral Tilt / Side Acceleration Node (NYL): Active
Adaptive Cruise Control Node (NAC): Not Active
Passenger Door Node (NPP): Active
Driver Seat Node (NAG): Not Active
Assistive Braking Node (NBA): Not Active
Passive Entry: Active
Steering Lock Node (NBS): Active
Gear Shift Node (NSC): Not Active
Passenger Seat Node (NAP): Not Active
Parking Sensor Node (NSP): Not Active
Engine Signals Node (NSM): Not Active
Airbag Node (NAB): Active
Air Suspension Node (NMA): Not Active
Roll/Incline Control Node (NPS): Not Active
Adaptive Headlights Node (NFA): Not Active
Drivetrain Control Node (HALF): Not Active

OSIONING TO NONE:
Reading CAN configuration data ...
CAN CONFIGURATION DATA:
04 32 97 FB 04 32 97 FB 00 00 00 40 00 00 00 00 00 00 00 00
04 32 97 FB 00 22 05 89 04 32 97 FB 00 22 05 89 00 22 05 09
32 31 31 34 30 30 30 36 35 30 32 4F 55 54 50 55 54 2D 4A 49 54 20 06 07 28 FB 97 32 04 89 05 22 00 C3 60 00 07 B7 00 34 10 00 00 94 06 01 00 01 06 08 00 00 22 50 57 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 42 40 B2 88 00
Body Computer (NBC)
Engine Control (NCM)
Instrument Cluster (NQS)
Steering Wheel Switch Node (NVO)
Radio/Navigation with Maps Node (NRR/RMN)
Brake System Node (NFR)
Info-Telematics / MS Convergence Node (NIT/NCV)
Driver Door Node (NPG)
Trunk Node (NVB)
Air Conditioning Node (NCL)
Steering Angle Sensor Node (NAS) C-CAN
Yaw/Side Acceleration Node (NYL)
Passenger Door Node (NPP)
Teg Reader Node (NPS)
Steering Lock Node (NBS)
Airbags Node (NAB)
2017-02-03 17:41:36
CONNECTED TO:
Alfa Romeo 159 1.9 JTDm 8V
CAN Setup / PROXI Alignment Procedure
--------------------------------------------------------------

Body Computer (NBC): EOL Ok
Engine Control (NCM): Ok
Instrument Cluster (NQS): EOL Ok
Steering Wheel Switch Node (NVO): Ok
Radio/Navigation with Maps Node (NRR/RMN): Ok
Brake System Node (NFR): Ok
Info-Telematyczny / MS Convergence Node (NIT/NCV): EOL Failed
Driver Door Node (NPG): EOL Ok
Trunk Node (NVB): Ok
Air Conditioning Node (NCL): EOL Ok
Steering Angle Sensor Node (NAS) C-CAN: Ok
Yaw/Side Acceleration Node (NYL): Ok
Passenger Door Node (NPP): EOL Ok
Teg Reader Node (NPS): Ok
Steering Lock Node (NBS): EOL Ok
Airbags Node (NAB): Ok

ACTIVATION OF REGULATIONS...
Displayed information
Old value: Type 1/Blue&Me
New value: Type 1/Blue&Me
COMPLETED


ACTIVATION OF REGULATIONS...
Displayed information
Old value: Type 1/Blue&Me
New value: None
COMPLETED


ACTIVATION OF REGULATIONS...
PROXI PROXYING PROCEDURE
Saving CAN configuration data ...
Saving to module: Body Computer (NBC) FAILED! - Error: configuration not supported by the system
Saving to module: Instrument Cluster (NQS) SUCCESS!
0
0
0
0
0
0
Saving to module: Info-Telematics / MS Convergence (NIT/NCV) FAILED! - Timed out
Saving to module: Driver Door Node (NPG) SUCCESS!
Saving to module: Air Conditioning Node (NCL) SUCCESS!
Saving to module: Passenger Door Node (NPP) SUCCESS!
Saving to module: Steering Lock Node (NBS) SUCCESS!
EXECUTION FAILED
Body Computer (NBC) FAILED! - Error: configuration not supported by the system

OSIONIATION TO: Type 3/Blue&Me Nav

Reading CAN configuration data ...
CAN CONFIGURATION DATA:
04 32 97 FB 04 32 97 FB 00 00 00 41 00 00 00 00 00 00 00 00
04 32 97 FB 00 22 05 89 04 32 97 FB 00 22 05 89 00 22 05 09
32 31 31 34 30 30 30 36 35 30 32 4F 55 54 50 55 54 2D 4A 49 54 20 06 07 28 FB 97 32 04 89 05 22 00 C3 60 00 07 B7 00 34 10 00 00 94 06 01 00 01 06 08 00 00 22 50 57 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 42 40 B2 88 00
Body Computer (NBC)
Engine Control (NCM)
Instrument Cluster (NQS)
Steering Wheel Switch Node (NVO)
Radio/Navigation with Maps Node (NRR/RMN)
Brake System Node (NFR)
Info-Telematyczny / MS Convergence Node (NIT/NCV)
Driver Door Node (NPG)
Trunk Node (NVB)
Air Conditioning Node (NCL)
Steering Angle Sensor Node (NAS) C-CAN
Yaw/Side Acceleration Node (NYL)
Passenger Door Node (NPP)
Teg Reader Node (NPS)
Steering Lock Node (NBS)
Airbags Node (NAB)
2017-02-03 17:31:37
CONNECTED TO:
Alfa Romeo 159 1.9 JTDm 8V
CAN Setup / PROXI Alignment Procedure
--------------------------------------------------------------

Body Computer (NBC): EOL Ok
Engine Control (NCM): Ok
Instrument Cluster (NQS): EOL Ok
Steering Wheel Switch Node (NVO): Ok
Radio/Navigation with Maps Node (NRR/RMN): Ok
Brake System Node (NFR): Ok
Info-Telematyczny / MS Convergence Node (NIT/NCV): EOL Failed
Driver Door Node (NPG): EOL Ok
Trunk Node (NVB): Ok
Air Conditioning Node (NCL): EOL Ok
Steering Angle Sensor Node (NAS) C-CAN: Ok
Yaw/Side Acceleration Node (NYL): Ok
Passenger Door Node (NPP): EOL Ok
Teg Reader Node (NPS): Ok
Steering Lock Node (NBS): EOL Ok
Airbags Node (NAB): Ok

ACTIVATION OF REGULATIONS...
Displayed information
Old value: Type 1/Blue&Me
New value: None
COMPLETED


ACTIVATION OF REGULATIONS...
Line input audio
ACTIVATION OF REGULATIONS...
Audio output
ACTIVATION OF REGULATIONS...
PROXI PROXYING PROCEDURE
Saving CAN configuration data ...
Saving to module: Body Computer (NBC) FAILED! - Error: configuration not supported by the system
Saving to module: Instrument Cluster (NQS) SUCCESS!
0
0
0
0
0
0
Saving to module: Info-Telematyczny / MS Convergence (NIT/NCV) FAILED! - Timed out
Saving to module: Driver Door Node (NPG) SUCCESS!
Saving to module: Air Conditioning Node (NCL) SUCCESS!
Saving to module: Passenger Door Node (NPP) SUCCESS!
Saving to module: Steering Lock Node (NBS) SUCCESS!
EXECUTION FAILED
Body Computer (NBC) FAILED! - Error: configuration not supported by the system



ACTIVATION OF REGULATIONS...
Displayed information
Old value: None
New value: Type 3/Blue&Me Nav
COMPLETED


ACTIVATION OF REGULATIONS...
Displayed information
Old value: Type 3/Blue&Me Nav
New value: Type 1/Blue&Me
COMPLETED

Maybe one of the control units is simply dead? maybe Blue&Me? and that causes the error??? ??
 
something is off with your configuration. You mentioned it might have been navigational before; if you mean the original, perhaps something remained after it and you need to unplug the cable? That telemetry/Convergence node with the error just doesn’t fit with me. I don’t want to scour the eLearnies to see what it is, but I think I don’t have it. Maybe someone else will chime in how it should be, because I can’t recall from memory.
 
Looks like that’s what’s happening.

Curiously I checked in my car, and it contradicts what I wrote in one sentence earlier, there is, however, an info-telematic/convergence node:
Proxi1.jpgProxi2.jpg

My configuration is Distinctive 2010 model X9 in Italian spec (without nav), plus xenon headlights, front PDC and blue&me added by me.

Probably won’t help, but perhaps it’s worth trying with the latest MES (currently 3.4), although I know that some earlier versions about a year ago nicely did the Proxi after adding B&M.
 
A lot of disassembly of the glove box to get to the blue&me ECU? I think if I disconnect it + set radio NONE it should settle the issue?? Additionally I read that you should do this in the English MES version rather than Polish??

Sent from my SM-G903F using Tapatalka
 
Correct, the ECU is under the radio, you must first remove the radio. Do not touch any compartments.

I have MES set to the English version, somehow I prefer it, translations in programs are often poor. You can change it in MES settings.

Quick note: after unplugging the B&M it might be necessary to change Audio output if possible (not at the car but in simulation these options are inactive) to some disabled? It’s also possible that Information displayed should be set to None so it doesn’t display some nonsense from B&M when you unplug it (unless then you lose radio notifications as well, so try other types; maybe Type1 can still remain? I don’t remember how it was for me before adding B&M).

EDIT. From old screenshots I know that when I added B&M on MES 2.8R1. from the logs the only change I made was Information displayed from None to Type1/BlueMe
 
Last edited:
Correct, the ECU is under the radio, you must first remove the radio. Do not touch any compartments.

I have MES set to the English version, somehow I prefer it, translations in programs are often poor. You can change it in MES settings.

Quick note: after unplugging the B&M it might be necessary to change Audio output if possible (not at the car but in simulation these options are inactive) to some disabled? It’s also possible that Information displayed should be set to None so it doesn’t display some nonsense from B&M when you unplug it (unless then you lose radio notifications as well, so try other types; maybe Type1 can still remain? I don’t remember how it was for me before adding B&M).

EDIT. From old screenshots I know that when I added B&M on MES 2.8R1. from the logs the only change I made was Information displayed from None to Type1/BlueMe


This has no impact on the alignment pass. You can set any values.
 
And problem is solved - the Blue&Me central unit is faulty. After disconnecting the central unit - and turning it off in MES the gauge stops flashing. But you can see that some magician has already tinkered with it... ;(
20170204_170053.jpg

and he probably poked something into that "resistor" or whatever it's called, because it looks like this:
20170204_170211.jpg
 
This has no impact on the alignment pass. You can set any values.

Maybe in these parameters it doesn’t matter, although a few months ago I was helping Pawelek_S add a B&M, I don’t remember exactly what he set incorrectly in Proxi, but it wouldn’t pass alignment with the wrong setting. Only when I set it as I told him did it go. My knowledge is just modest experience with adding it and helping a few other people. I know (read somewhere on the forum) that there were problems in older MES versions, probably below 1.something.

- - - Updated - - -

And problem is solved - the Blue&Me central unit is faulty. After disconnecting the central unit - and turning it off in MES the gauge stops flashing. But you can see that some magician has already tinkered with it... ;(
View attachment 221230

and he probably poked something into that "resistor" or whatever it's called, because it looks like this:
View attachment 221231
I’m not sure whether to try to repair, or maybe better to buy a cheap one (the price range on Alledrogo is usually big, those from Media can be bought for 100zł or 500, so you probably need to hunt for a bargain).

Choose replacements with the help of the ePer (the previous and next compatible for your current one), also check whether the one you have matches your car - maybe someone has already tinkered.
 
Last edited:
yeah? I’m curious how you’re sure it’s the one you have fits MaTe? I ask because for the X9 model (2008-2010) ePer lists 7 different central units, and only one of them is for the large navigation, two or three for blue&me + this primitive radio-navi. There are probably some differences, and it’s not known whether a random one will work without issues or if you’ll need to do some tinkering.
MaTe has 1.9 8V, so the X3 or X9 model.

Here’s a paste from ePer for X9:
5 50514602 BLU & ME NAWIG. 55Y 01
5 50512729 BLU & ME 4J3 + !4CU + !5VZ C13463 01
5 50512934 BLU & ME 4J3 + 4ZS C13463 01
5 50518240 BLU & ME 4CU + 4J3, 5VZ + 4J3, 5VZ + 4J3 + 4FT + 5JW + 5EV + 4YD + 341 01
5 50518241 BLU & ME 4ZS + 4CU, 4ZS + 5VZ 01
5 50518381 BLU & ME 4J3 + (717, 564) D13463 01
5 50518382 BLU & ME 4ZS + (717, 564) D13463 01
and here central units for model X3 (2005-2008):
5 50511183 BLU & ME NAWIG. E55Y 01
5 60699960 BLU & ME E55G C10960 01
5 50505921 BLU & ME E4J3 D10960 01
 
Last edited:
I have model 50514602, didn’t have Navi, only a regular radio. I swapped to a 2-DIN radio and therefore I offered it.

- - - Updated - - -

MaTe is labeled 50505921 which means X3; I have 50514602 which is X9 but it still matches, i.e. BLU & ME NAWIG. 55Y 01
 
the names of options don’t necessarily guarantee compatibility, although they give some hope, you have to check part compatibility, not only functional.

but something doesn’t fit. you say there are identical option names and you say MaTe has 50505921 (where do you know that from, I don’t see that info in the thread). E4J3 (i.e. B&M) are not the same options as yours (55Y) - you have radio-navigation and he doesn’t. in my view that’s worse, it may work or may not.

In the ePer for your 50514602, replacements give me: 50513709, 50511183, 60699961

Replacements for 50505921 are 51989250, 51943247, 51946545.

According to ePer they are not compatible, but it’s probably also about functionality, that the first ones additionally have navigation. So yes, risky to buy. Unless you share it for checking, then trying wouldn’t hurt.
 
Last edited:
Amortyzatory
Back
Top