• Jeśli chcesz dodać swojej Alfie charakteru i jednocześnie zaznaczyć przynależność do naszej społeczności – to dobry moment, żeby je zamówić.

    Ramki Alfaholicy

    Szczegóły, zdjęcia oraz informacje o zamówieniu znajdziesz tutaj.

    Nie czekaj, bo jak zwykle schodzą szybko.

Disabling start/stop

https://youtu.be/PlwKxytZjI0

A solution on how to disable it [emoji3]
If the guy has a plate, he will let me know. For now he made one and it works as in the video. After pressing and holding for 5 seconds, the plate turns off (no visit to the dealer). Then again 5 seconds holding turns the plate on. Sent from my HMA-L29 using Tapatalka
send the contact to some page, or email/tel to the guy. he has it nicely done on plugs, or do you need to solder into the original harness? I suppose the system simply simulates pressing the button after power-up according to the last set 5s pressing state for S&S. I also suppose that pressing the button for the bus is a change of resistance from one to another (need to measure) - in Fiat/Alfa for years, various buttons/states e.g. locks etc are reported to computers in this way. if this guy dodges it too much, maybe I’ll do something similar myself someday, but if he has a ready-made with plugs, I’d rather buy it.
 
send the contact to some page, or email/tel to the guy. he has it nicely done on plugs, or do you need to solder into the original harness? I suppose the system simply simulates pressing the button after power-up according to the last set 5s pressing state for S&S. I also suppose that pressing the button for the bus is a change of resistance from one to another (need to measure) - in Fiat/Alfa for years, various buttons/states e.g. locks etc are reported to computers in this way. if this guy dodges it too much, maybe I’ll do something similar myself someday, but if he has a ready-made with plugs, I’d rather buy it.
https://rover.ebay.com/rover/0/0/0?mpre=https://www.ebay.co.uk/ulk/itm/322352078637

This is some Hungarian guy. Sent from my HMA-L29 using Tapatalka
 
in theory that much can be done, it’s a pity to fiddle with making a plate yourself, better to buy some small microcontroller etc. the only thing is the wiring. on one hand the guy writes: NO need to cut anything, just need to connect 3 wires. on the other hand he sells a device without some plug - in the photos three wires without ends. when you talk to him ask about this matter - I’d prefer to hook it up as an adapter between the original panel plug and the car's wiring, so that if needed it won’t deactivate it, and you can unplug it. so today I’ll have to remove this panel to decipher what plugs there are, whether something standard can be made. I’ll let you know.
 
Last edited:
in theory that much can be done, it’s a pity to fiddle with making the plate yourself, better to buy some small microcontroller etc. the only thing is the wiring. on one hand the guy writes: NO need to cut anything, just need to connect 3 wires. on the other hand he sells a device without some plug - in the photos three wires without ends. when you talk to him ask about this matter - I’d prefer to hook it up as an adapter between the original panel plug and the car's wiring, so that if needed it won’t deactivate it, and you can unplug it.
If I write that he has it, I’ll ask for details. Sent from my HMA-L29 using Tapatalka
 
I did it, tested, refined my version of disabling S&S. I did it a bit differently than the guy from eBay, 4 wires under control with LED indicator (for example in my Giulietta if I turn off the car for a moment it remembers, the guy’s solution then turns S&S on - I control and if not needed I do not simulate pressing the button). It’s possible to deactivate etc. After reprogramming it ends in the programmed state. I also made it as an adapter plugged between the light panel and the car's harness. Here is a beta version from the first tests:

https://photos.app.goo.gl/JgrybWLBoJ64jHNw6

I’m wondering now if people would be interested and at what price as acceptable. remember this is a niche market, and it certainly cannot cost below 120 if this is to be a finished product, professionally done and not just something. I’m not interested in a few units sold - if I do this it would be a normal business, i.e., dedicated/compact enclosure, dedicated PCB, outsourcing soldering/testing to a tech and selling via an online shop. Ideally I’d like to make it as a ready adapter plugged between the harness and the panel, as in my prototype, only I didn’t have the right connector, so only connectors are plugged and secured with zip ties so they don’t pull out - the final product would need connectors (which I might order at least based on some standard connector components I now use - such a solution is costly and both plug designs). I could also make a simple version with 4 wires plugged into the harness with soldering or quick disconnects (or 3 cables - I can disable LED control in the program). Please comment here on the forum. I won’t make single units - as I said I don’t have time. Simple installation, but I probably won’t play with it - if a business starts, I agree with a few workshops in Poland to handle it.
 
Last edited:
Polish market probably won’t satisfy the need for 100+ devices investment
 
Polish market probably won’t satisfy the need for 100+ devices investment
If I could sell this series for 100 right away in the first 3 months, I could maybe launch such a series, and in the meantime try to offer it abroad. Let’s say 30 solid customers on Alfaholics could persuade me to invest in 100-200 units.

Do you necessarily want in-between wiring between the original harness and the panel? Or maybe removing 4 pins and an adapter that fits this? Or quick connectors or soldering across 4 lines would also work? The last solution is the simplest, it could significantly speed up the product launch deadline. The second solution is I have to look at the plug to see if pins can be removed without issue.

dedicated enclosure or some universal will also work?
 
If I could sell this series for 100 right away in the first 3 months, I could maybe launch such a series, and in the meantime try to offer it abroad. Let’s say 30 solid customers on Alfaholics could persuade me to invest in 100-200 units.

Do you necessarily want in-between wiring between the original harness and the panel? Or maybe removing 4 pins and an adapter that fits this? Or quick connectors or soldering across 4 lines would also work? The last solution is the simplest, it could significantly speed up the product launch deadline. The second solution is I have to look at the plug to see if pins can be removed without issue.

dedicated enclosure or some universal will also work?

do you have a photo of this connector/socket?

btw this system will probably handle not only Alfas but other marques as well, so there is some market potential.

in
 
something like:
20190216_132459.jpg20190216_132516.jpg
as for the spacing, normal IDC pins 2x6 fit, only at my own car I didn’t secure with zip ties but wrapped with insulating tape; during insertion/removal multiple times (reprogramming) the harness bent and, anyway, stuck out enough on one side, so lights were permanently on and the 0/Auto/On dial didn’t work. out of curiosity I checked ePera for a connector, but I didn’t find that one, though other simple connectors—guess how much they charge—everything shows 371 PLN/piece...

as for other cars, yes, though here a certain problem might be the different control methods. how it is in other cars is unknown - I’d have to mix and match versions, or a bigger board that can handle different interface types. from the digital side I can do anything programmable ( timings, control type/polarity, confirmation type, etc.). however, regarding release of any version for another car, you’d need physical access to the car, an owner willing to remove the panel and tinker (physical measurements/oscilloscope (in Giulietta the LED diode is checked too and also works as PWM), tests, etc.), and time to arrange and tinker - that’s the biggest problem. I think for now, if anything, it will be the case Giulia/Stelvio, I’ll check while at it how it works in my wife’s Giulietta (in hers the car remembers, so no problem, but many have a G with no memory of SS). if something looked promising, we could think about other cars. we’ll see, we’ll see, I still don’t know if I need it, my work is good, I design complex devices that give satisfaction, money is good. On the other hand, I’m tempted to start my own business - haven’t done that yet.
 
I’m back with a small update, although some people have been in touch with me, so they know. I hope I don’t violate the forum rules with the following post, and that you’ll turn a blind eye to an old colleague?

I’ve started a new business. Soon a shop and various items on stuff4car.com. for now I have a bypass SGW for FCA group cars and soon a production-ready start&stop deactivator, not like the one I showed in the video a few months ago. made on original sockets/connectors so no traces left in the car, no soldered connections to the car harnesses that could later be cited by the dealer as a warranty excuse. plus my guy checks the status of the LED diode, so nothing will fool him. you can also deactivate the device, and in the future if FCA changes something in BCM software with an update, there will be a Mini USB connector and I can release a fix you can load from a laptop without problems.

Wires soldered, PCB boards for the first 120 units just arrived, rest of components in stock:
20190702_003206.jpg20190725_141841.jpg

The price will be a bit higher than I thought, but adding the original connector/socket and cables with compatible pins and the work involved are costs that surprised me. but I still concluded that this version is correct because it does not violate wiring/ warranty. I’m not yet giving prices because I want to build at least a few prototypes in the final version. There will definitely be a good discount for Alfaholics.

If there are many interested in a cheaper version without the original plug and only 4 wires to solder, we can consider it, though I won’t make many of those (because that comes with a lot of paperwork - warehouse system listing, production manual, user manual, new photos, etc).

Next week I plan to have a few pieces for those who have been harassing me by email/PM for this device for months. then 2 weeks vacation and after the vacation, after August 20 production will start and I’ll open an online shop. I’ll keep you posted.

please don’t start questions about prices or such things in this thread; keep it technical and informational that such a thing exists on the market, but for questions/orders there will be other contact methods on the store page.
 
Last edited:
a small update from me. I soldered today 5 prototype units, for now manual assembly (5 hours just soldering these 5 pieces, so it can’t be done this way long-term because the module would be too expensive due to other labor and costs). next week I’ll talk to the guy about automatic assembly.
I also have prototype housings, everything is tip-top so I ordered another 100 pcs.

This is roughly what it looks like after assembly:
20190727_154056.jpg20190727_163940.jpg20190727_164133.jpg

In-car assembly, with some practice, about 1 minute, first time about 3 minutes - you plug it between the light panel and the harness.

These 2 units with stickers are promised for the guys doomin13 and Suzumushi; if there are no problems/unexpected issues, by the end of next week I should be able to ship them. I could send 2 more if someone really wants.
Final price not set yet, I still need to cost the automatic assembly. A few units for Alfaholics will be 200 PLN gross (with VAT 23%) plus courier or parcel locker 15 PLN. Then I’ll set the final price for the production run and for Alfaholics there will be -10%.

I’ll post progress updates - this evening or tomorrow I’ll start porting code from the prototype on AVR to the final one on STM32. There are a few more things to change/add, I’ll work Mon/Tue during testing.

There is a mini USB port, so in case of updates for beta testers or if FCA changes something in BCM firmware, you can flash the update yourself from a PC.
 
Amortyzatory
Back
Top