• Jeśli chcesz dodać swojej Alfie charakteru i jednocześnie zaznaczyć przynależność do naszej społeczności – to dobry moment, żeby je zamówić.

    Ramki Alfaholicy

    Szczegóły, zdjęcia oraz informacje o zamówieniu znajdziesz tutaj.

    Nie czekaj, bo jak zwykle schodzą szybko.

Invalid ISO Code

kajak

New
Joined
Apr 28, 2020
Messages
15
Car
Giulia TI 2.0 280KM RWD
Hi everyone!

I’m the happy owner of another Giulietta from overseas - model year 2020. Of course a little dent and the pyrotechnic fired + fuel cut.
The fuse replaced with a new one, set from PMFactory + bypass epsonix (thanks a lot!), unfortunately trying to connect to the BCM to start the FIS procedure pops up a message that the ISO Code is incorrect and MES 4,7R3 can’t do anything about it, I press Y, and it automatically switches to simulation mode.
I also tried to connect to a mechanic’s diagnostic tools - unfortunately the same result, ISO message.

Is there any way to resolve this? Have you ever encountered such situations?

PS.
The paddle procedure doesn’t work (unless there are some conditions that must be met for it to work, about which I have no idea).
 
Because MES doesn’t have ISO codes for ECUs in cars from 2019 onwards. And this program isn’t kept up to date despite an email sent to the program developer for an update. try AlfaOBD.
 
Hi everyone!

I’m the happy owner of another Giulietta from overseas - model year 2020. Of course a little dent and the pyrotechnic fired + fuel cut.
The fuse replaced with a new one, set from PMFactory + bypass epsonixa (thanks a lot!), unfortunately trying to connect to the BCM to start the FIS procedure pops up a message that the ISO Code is incorrect and MES 4,7R3 can’t do anything about it, I press Y, and it automatically switches to simulation mode.
I also tried to connect to a mechanic’s diagnostic tools - unfortunately the same result, ISO message.

Is there any way to resolve this? Have you ever encountered such situations?

PS.
The paddle procedure doesn’t work (unless there are some conditions that must be met for it to work, about which I have no idea).

Do you have a purchased and paid license or only an interface with the free software.
 
ignorance of ISO codes is the norm - for example it’s probably the case at Giulias with the engine ECU, but due to practically no differences the program works. MES license purchased/activated? Do other computers work normally?
 
MES full, activated, all legit. Didn’t have a problem with an older Alfa, now it crashes with the newer one...
Today I’ll try AlfaOBD and will report back ;)

Additionally the odometer started flashing...
 
weird. what did you do that made the mileage flash? some proxy that didn’t pass? are all fuses OK?
 
I’m not sure if it started now or it was flashing earlier - I just noticed it now.
Because of the ISO error it doesn’t even want to enter PROXI.

#Update
Now when starting the FIS procedure, it shows the message, "Incorrect conditions to run this test".
Any info on exactly what must be okay? Oils? Fluid? Errors? Sensors? Cushions? Belts?
 
How to check exactly if the SGW is detected?
When it’s connected it blocks executing any MES functions, so in my opinion it’s working correctly.

I repeat the question:
Now, when starting the FIS procedure, the message appears, "Incorrect conditions to run this test".
Any info on what exactly must be correct? Oils? Fluids? Errors? Sensors? Cushions? Belts?
 
I’m reading this thread and nodding my head in awe at the courage and determination. I have trouble scheduling a normal routine service at a German authorized service center and the car is fully functional and still under factory warranty. I can’t imagine being in a situation like Kajak and others. Science fiction to me. I also admire this knowledge... Pole can do it!
 
Amortyzatory
Back
Top