• Jeśli chcesz dodać swojej Alfie charakteru i jednocześnie zaznaczyć przynależność do naszej społeczności – to dobry moment, żeby je zamówić.

    Ramki Alfaholicy

    Szczegóły, zdjęcia oraz informacje o zamówieniu znajdziesz tutaj.

    Nie czekaj, bo jak zwykle schodzą szybko.

Error P0115 - Engine coolant temperature

jan3387

New
Joined
Nov 29, 2014
Messages
130
Location
Bielsko-Biała
Car
Alfa Romeo Giulia Super 2.2 M-jet MT 180 KM '16
Hello,

I got an error while starting the vehicle as in the title. After connecting Car Scanner and clearing the error it reappeared after two days. The car runs, consumes fuel, and accelerates normally. The coolant temperature on the gauges shows a normal temperature. On August 1 I’m going to replace the external temperature sensor in the mirror - currently it shows -24.

What could be the cause of this error?
 
Battery charged? maybe a glitch/false read from a voltage drop at startup when it kicks in during starting?
 
Right, I don’t know. Earlier I had P0100 - Mass Air Flow sensor/Volume Air Flow, but after clearing it doesn’t appear anymore. I drive long distances, so it’s probably charged. From what I read, such errors occurred in older Alfa models; overall everything mechanical seems fine, I’m afraid there’s something happening with electronics.
 
Maybe the battery is already old, which with a super dumb charging strategy ages the battery faster, especially one that never charges above about 80% (for people who drive 1–2 thousand km per week, because normal mortals vary, even 30–40% for those who live near the boiler to a max 75% turning off S&S but not driving long trips, just medium)?

Start with charging a decent battery - if you have an original Varta HD or another EFB, it’s best in Recond/Repair mode if your charger supports such a thing (in this mode charge the battery with the earth disconnected because officially max is 14.7V and in Recond on low currents it climbs to about 16V). If you already changed to AGM then no recond!

Update, bring what the Service updated?
 
The battery is at max 3 years (it’s the original Varta with AR logo - replaced when the car was purchased at the BB showroom in December 2020 (executive car)). Unfortunately I don’t have a charger or meter. But I did a test today and didn’t disable start & stop (I always disable it). Start & stop works, so I assume the battery is probably OK.

Update: they did me a replacement for the radio from generation II two years ago. But you think that this is probably not a mechanical fault since the engine runs normally?
 
If S&S works then the battery is charged to more than 65%, of course how much of the starting capacity remains is another matter, but since you normally do trips and disable S&S there won’t be a disaster. So probably not this path.

Check if the negative terminal cable is clamped (even in the ASC they sometimes don’t fit it well) - pull it or see if it loosens, also look at the positive terminal to see if it’s tight. I know a case where a guy had issues after half a year and it turned out the + terminal was loose when he pulled it.

Visually also check for any strange deposits there.

If OK, you need to look further - from simple things I would start by checking the grounding points from the fuse box to the engine/transmission (on a lift at a mechanic unless you have ramps nearby or a neighbor with a garage hoist) and the one from the battery to the body (you can check from the trunk), to ensure the battery electrical ground is solid. You can also check the tightening and appearance of the main fuses in the positive terminal box - but do this with the ground disconnected - it would be silly to touch ground with a wrench and blow the battery or weld the tool between terminal and body.

Another thing, see if any animal visits. signs of paws, crumbs in the engine bay.

Then only further diagnostics, but I don’t have an idea at the moment - I didn’t encounter this on forums before.

Since updates were done on the radio, likely other things too, and your car’s firmware is reasonably new.

Good luck.
 
I have a small update. After replacing the mirror temperature sensor the problem seems to have stopped. At the ASO in Bielsko I learned that it was related to that sensor which gave incorrect temperature to the system and manifested as errors 100 and 115. After connecting to the VDS the following interesting information appeared, which I’m attaching below. Namely, that there is some update still available for my vehicle?

Przechwytywanie.jpg


From other information, the Sales Center in BB and the service next to it are only until the end of November - then they close.
 
problems with the standard sensor from what I observe on the forum, mostly early 2016/17 models

campaign 6116 was in 2017 if I remember correctly and every car normally serviced had these updates installed, yours only now?
 
Nothing was installed for me. During the radio replacement they installed 6116. I just wanted to ask you whether the other side of the file I attached shows that there is something new to install.
 
No, on the first page it says they installed it, on the second apparently there is more to install - I don’t know, maybe the database hasn’t updated yet? Ask them - several modules were to be updated, I can’t remember which ones though I recall HVAC climate control to version 1025, others I won’t say.
 
The fuel pump relay under the headlight to be replaced.
External temperature sensor only indicates temperature and an additional reading for the climate control unit.
 
Who are you writing to? the latest posts are about campaign 6116 and this one mainly software updates or possibly tightening or replacement - please, from eLearna everything that is in this campaign:

Operations to check and restore conformity, if needed
• Operation A Check front differential tightness (AWD versions only).
• Operation B Replace and paint door mirror covers.
• Operation C Replace HALF control module.
Update electronic system SW
Update the software of the following vehicle electronic systems.
• Operation D Update ESL control module software
• Operation E Update BCM and RFHM control module software
• Operation F Update BSM control module software
• Operation G Update 7” IPC control module software
• Operation H Update 3.5” IPC control module software
• Operation I Update CDCM control module software
• Operation J Update ACC control module software
• Operation K Update HALF control module software
• Operation L Update HVAC control module software
• Operation M Update EPS control module software
• Operation N Update PAM control module software
• Operation O Update ECM control module software for 2.2 JTD
versions
• Operation P Update TCM control module software for 2.2 JTD
versions
• Operation Q Update ETM control module software (Including time for
preparation and position/removal of vehicle on workshop
lift).
• Operation R Update the maps
 
no, but on the first page it says they flashed, on the second supposedly to flash - I don’t know, maybe the database hasn’t updated yet? ask them - a few modules were supposed to be updated, I can’t recall which off the top of my head though I remember HVAC for version 1025, I won’t say others.

thanks for the help. By the way, do you have a good workshop for our Alfas in our city now that the dealer is closed?
 
unfortunately I don’t have another strictly Alfa workshop; I’ll do some things myself, some with a mechanic I’ve been going to for years with other Alfas whom I know and trust, but I won’t say who, because there’s already a long queue for him, I’d end up with an audience appointment in 3-4 weeks. he doesn’t even have Witecha sometimes or certain dedicated tools, so e.g. updates won’t be done or some mechanical things, though he has Texe containing all procedures in the computer e.g. for brake work - flushing etc (which MES doesn’t have), plus all documentation/descriptions and online catalog ePer, so together with me we’ll handle the car comprehensively.

I can’t imagine there won’t be a new AR service here - I think they want to scrap the old one because there are too many people working there, and build with someone new - perhaps they’ll pick out the better ones from the ASO in the necessary quantity to ensure staff, and some company/another dealer will cover it? In BB on the border with Jaworze there is Auto Spektrum but they only have Fiat/Fiat Professional with us (in another city in Poland they have Alfa), maybe they’ll get authorization and stock up the required equipment (back when I asked them when MES couldn’t handle proxi of some new modules (TBM) they claimed they couldn’t even do proxy with their Witech, probably even more so now, but maybe it will change)?
 
Who are you writing to? the latest posts are about campaign 6116 and this one mainly software updates or possibly tightening or replacement - please, from eLearna everything that is in this campaign:

Operations to check and restore conformity, if needed
• Operation A Check front differential tightness (AWD versions only).
• Operation B Replace and paint door mirror covers.
• Operation C Replace HALF control module.
Update electronic system SW
Update the software of the following vehicle electronic systems.
• Operation D Update ESL control module software
• Operation E Update BCM and RFHM control module software
• Operation F Update BSM control module software
• Operation G Update 7” IPC control module software
• Operation H Update 3.5” IPC control module software
• Operation I Update CDCM control module software
• Operation J Update ACC control module software
• Operation K Update HALF control module software
• Operation L Update HVAC control module software
• Operation M Update EPS control module software
• Operation N Update PAM control module software
• Operation O Update ECM control module software for 2.2 JTD
versions
• Operation P Update TCM control module software for 2.2 JTD
versions
• Operation Q Update ETM control module software (Including time for
preparation and position/removal of vehicle on workshop
lift).
• Operation R Update the maps

I’m saying that in most cases this error is caused by the fuel pump relay for the coolant electric pump, which was of poor quality up to 2019.
 
OK, maybe, but these new ones are also failing people - I’ve heard from Alfissimo - they’re looking for another brand hoping it will be better, although I think there’s simply a lack of a diode, wired in parallel with a blocking diode, to discharge the solenoid coil without arcing at the contacts and thus their burning over time.
 
Amortyzatory
Back
Top