• Jeśli chcesz dodać swojej Alfie charakteru i jednocześnie zaznaczyć przynależność do naszej społeczności – to dobry moment, żeby je zamówić.

    Ramki Alfaholicy

    Szczegóły, zdjęcia oraz informacje o zamówieniu znajdziesz tutaj.

    Nie czekaj, bo jak zwykle schodzą szybko.

Dynamometer chart

method

New
Joined
Apr 5, 2012
Messages
475
Location
Lublin
Car
Giulia 2.0 RWD MY'20
hey

I ordered today Julka, to see if the factory is cheating me ;)

the chart in the attachment (of course Dynamic mode), a little worrying a dip around 5000. According to the guys from the shop, at fairly high temperatures the intercooler may not keep up and the engine puffs up, we are wondering about swapping to a bigger one and a virus :)

Julka is stock (1.4 MA) except for the Ragazzon exhaust and BMC air filter.
 

Attachments

  • Giulietta 1.4.jpg
    Giulietta 1.4.jpg
    99.3 KB · Views: 953
Thanks! I was looking for such an image two years ago. What worries me more is the torque curve - nothing happens before 2,000 and here it is shown nicely and scientifically.
 
The chart is rather imprecise because the description indicates the maximum power is reached at 5560 rpm, while the chart shows something else... Putting aside these minor details you can see that the engine holds factory parameters, and the chart itself shows why it’s not worth revving this engine above 4200 rpm if you want to accelerate dynamically (flat torque curve in the range 2100-4200 rpm)
 
Last edited:
This is a petrol engine - who drives it below 2 thousand rpm?!

Spare me the demagoguery. This is a petrol engine, but it doesn’t wow in any special way. The 1000-2000 range is more important to me than 5000-6000. And there nothing happens there.

- - - Updated - - -

Probably some old guy :), or someone after switching from a diesel.

Or from a petrol one, which has a steady and maximum torque already from 1500.
 
Spare me the demagoguery. This is a petrol engine, but it doesn’t wow in any special way. The 1000-2000 range is more important to me than 5000-6000. And there nothing happens there.

but this chart is no secret, nor any revelation.
how would a turbo engine even work?
ok, maybe indicate an engine that has a steady and maximum torque from 1500 rpm.
 
personally I don’t mind that little happens below 2000, honestly I’d prefer the top end to be better, and currently it does seem that above 5000 there’s little point in revving (plus that dip). I hope that after swapping the intercooler and virus-ing the benefit from the top will be bigger ;P I regret we didn’t do 2 measurements in D and N, I’d like to catch the difference on the chart, the power is the same but the torque curve is different
maybe someone has a chart in N mode?
 
personally I don’t mind that little happens below 2000, honestly I’d prefer the top end to be better, and currently it indeed seems that above 5000 there’s little reason to rev (and this dip). I hope that after replacing the intercooler and virusing the benefit from the top will be greater ;P I regret we didn’t do 2 measurements in D and N, I’d like to capture the difference on the chart, power is the same but the torque curve is different
maybe someone has a chart in N mode?

Can you provide information how much such a virus costs? and what intercooler replacements you will be doing? what are the costs as well?
 
Forgive the demagoguery. This is a petrol engine, but it’s not particularly impressive. The range 1000-2000 is more important to me than 5000-6000. And there, nothing happens.

- - - Updated - - -



Either from a petrol engine, which has a constant and maximum torque starting at 1500.

This isn’t demagoguery, but realities backed by knowledge from the field of mechanics. Read about how some engine components (main bearings, connecting rod) take a beating when driving at low revs with full load. I’ll skip the fuel consumption with such inefficient engine use. Show me a petrol engine of similar size with 4 cylinders having constant and maximum torque from 1500...?! Even in 8-cylinder units it would be a problem.
 
Can you provide information how much such a virus costs? and what intercooler replacements you’ll do? what about the costs as well?

the cost of chiptuning is usually determined individually depending on what else will be done (the chiptuning itself around 1500). There is a lot of space in the front bumper for an intercooler, no decision yet on which one exactly, surely some universal one higher than stock, the cost of the intercooler itself ~ 400 PLN. This month I probably won’t do it because finances won’t allow ;)
 
This isn’t demagoguery but realities backed by knowledge from the field of mechanics. Read about how some engine components (main bearings, connecting rod) take a beating when driving at low revs with full load. I’ll skip the fuel consumption with such inefficient engine use. Show me a petrol engine of similar size with 4 cylinders having constant and maximum torque from 1500...?! Even in 8-cylinder units it would be a problem.

Yes, a bit of demagoguery, because both you and the previous posters cite extreme cases. Although perhaps I started by writing that “nothing happens.” Something does happen, but not too much. The key word above is “of similar size,” because this might simply be too small a engine to set the bottom end properly. I don’t know how it is with those 160/170 hp 1.4 TSI, perhaps similarly. I had an 1.8 TSI 160 hp and the bottom end was much better. And the new BMW engine for the current 20i versions has 270 Nm from 1200 to 5000, but that is two liters and maybe a bit unfair to compare, because it’s a different league. Regarding the bearing and crankshaft durability, without being an expert I joyfully assume the designers planned these elements to bear the maximum available stock torque. Recently I read that someone’s crankshaft “reared its head through the sump,” which concerned a specifically modified engine. Somehow there isn’t a mass problem with shafts and bearings, unlike e.g. turbos, DPFs, dual-mass flywheels, and clutches? Indeed, accelerating at full boost from 1000 RPM is a not-so-smart idea, but actively using this range during normal driving isn’t necessarily. For example, again BMW, this time 328i, probably around 250 hp, when driving calmly drops revs to about 1300, where it already has maximum torque, I think around 320, don’t remember. This is how petrol engines are made nowadays, so maybe don’t tell me about grandfathers, diesels, or whatever, because technology moves forward. At least that’s what I think. Well.

- - - Updated - - -

This isn’t demagoguery. After a spin in a Ferrari you’d also say it’s useless, because below 2k nothing happens? The fact that the MA isn’t particularly impressive is another matter...

Ferrari is useless, because it would stall on the garage incline. :D
 
Have any charts appeared in the meantime for other modes, e.g. N or A?
 
Look in the tuning section,

Sent from my EVA-L09 using Tapatalka
 
Amortyzatory
Back
Top