• Jeśli chcesz dodać swojej Alfie charakteru i jednocześnie zaznaczyć przynależność do naszej społeczności – to dobry moment, żeby je zamówić.

    Ramki Alfaholicy

    Szczegóły, zdjęcia oraz informacje o zamówieniu znajdziesz tutaj.

    Nie czekaj, bo jak zwykle schodzą szybko.

Check Engine

That the car disconnects the D&A and S&S after a check engine is normal.
And the rough running at idle is 99% Multiair.
Error codes?
 
That the car disconnects the D&A and S&S after a check engine is normal.
And the rough running at idle is 99% Multiair.
Error codes?

there are no faults.

Only occasionally the engine light comes on and the Start&Stop is disconnected. Video below:



Maybe let’s add a few examples of Multiair failures to the thread so it’s clear what we’re dealing with and how to spot that this is it. At first glance, my father doesn’t have problems with it.

Example of Multiair failure heard from inside the car (I recommend using headphones to hear clearly the faulty MA clatter at idle).

https://www.youtube.com/watch?v=B9aUXu4Ig7I

Outside you can hear it roughly like this (you hear an extra clatter as if a vent is letting air out, sometimes it disappears)

https://www.youtube.com/watch?v=vr9d7uCMfQE

and this is Multiair.

Whereas at my father’s it doesn’t look like that.
 
Last edited:
now it should work because at first I put to Privat so it didn’t work now it should be OK.
 
Gentlemen I’m uploading a video of how the engine runs,
These engines and TK never had great idle quality as I’ve written before on the forum, so I think its operation here isn’t bad and doesn’t indicate a damaged module. MA what do you think?
Honestly, it runs better than when it was new.

 
Last edited:
And replacement MA happened :) Fiat paid most of the money (70%) so I won’t criticize.

The car is almost 6 years old and is already after an extended warranty. serviced at the official dealer.
There wasn’t a war, they just covered the costs, the car now runs very well.
 
Last edited:
Good day Gentlemen

I have a Giulietta 1.6 JTDm from 2013, 105 HP...

The check engine light and the orange triangle lit up at the same time...
Any suggestions what it could be? EGR? Injectors? Fuel filter? Unfortunately I can’t provide the error code...
The engine runs normally
 
Hey,

from the manual if you don’t have an error code it may be for example:
General fault
(yellow-orange triangle)
(for versions/markets where provided)
The warning light will come on in the following
cases. Contact the official dealer as soon as possible Alfa
Romeo, to eliminate the damage.
Exterior lighting fault
See description for the warning light 6.
Brake light fault
See description for “Brake light fault”.
Fuel vandalism? actually Fuel cut-off lock
The warning light will come on when the fuel cutoff switch is involved. The appropriate message will appear on the display.
Start & Stop fault
(for versions/markets where provided)
The warning light will come on when a Start&Stop system fault is detected.
Rain sensor fault
Parking sensor fault
(for versions/markets where provided)
See description for the warning light t.
Dusk sensor fault
(for versions/markets where provided)
The warning light will come on when a dusk sensor fault is detected.
AFS lighting adaptation fault
(for versions/markets where provided)
The light will come on when an AFS headlamp alignment fault is detected
(the “AFS headlight adjustment” description in this chapter). The appropriate message will appear on the display.
Convex window protection system fault
The warning light will come on when a moonroof? Actually the system to prevent squashing by the window is detected. The appropriate message will appear on the display.
Oil pressure sensor failure in the engine
The warning light will come on when the oil pressure sensor malfunction is detected. An appropriate message will appear on the display.
 
Hello Alfa fans, using the topic that there already is one, I have problems with my Julia 2010 1.4 MA 170 hp. At the beginning of this year I sent the module for regeneration because it started throwing p0300 etc errors. Since temperatures dropped, Julia starts badly, it throws errors p0300 p0301 p0303 p0304 (I understand that it’s misfire on cylinders 1 and 4). The engine runs poorly only after a long idle and when the temperature drops at night. When it’s about 5 degrees above zero, I start it and it runs normally. I’m attaching a link to a video below.

https://www.youtube.com/watch?v=n-fUdfNyFKI&ab_channel=WojciechBrandt
 
you simply start it, wait for the tractor in the engine to settle, and you drive away without issues.

With MA it’s like with eggs, especially in frost.
 
But it runs so hard? This is really scary, sometimes I fear something inside might come apart :/
 
But it runs so hard? This is really scary, sometimes I fear something inside might break loose :/
What oil is in it? P.S. Nothing will happen to the engine
 
But it runs so hard? This is really scary, sometimes I fear something inside might break loose :/
Hello
I have a similar situation where no dashboard message appears. The problem with stalling occurs after I drive several dozen meters. Then it does not inform me e.g. to shift to a higher gear; after driving, say, 1 km, the engine starts running normally, and then the icon about changing gear appears. Recently it was only with a cold engine, as soon as the temperature gauge needle trembled the cause was found and there was no problem until the end of the drive, though it did not always behave like that. Now the problem has worsened and even while driving when the engine has reached operating temperature it can vibrate, there is no power, no error appears and the car stalls after a few meters, then it continues normally. Any ideas? What could it be? It started behaving like this about 2 weeks after the timing belt replacement. Spark plugs and coils were replaced but still nothing. I'm already worried because I went to one and another and third mechanic and nothing improved. And replacing something every now and then that turned out not to be necessary just generates costs, and the problem remains. Help
 
I have a question. I connected MES to the engine control unit and despite no errors in the Errors tab, in the Parameters tab under the Failure indicator I see the message - Flashing, and under the Engine start parameter - disallowed. Is something wrong with MES, or with the car? The engine runs normally.

awaria-01.jpg
 
Amortyzatory
Back
Top