• Jeśli chcesz dodać swojej Alfie charakteru i jednocześnie zaznaczyć przynależność do naszej społeczności – to dobry moment, żeby je zamówić.

    Ramki Alfaholicy

    Szczegóły, zdjęcia oraz informacje o zamówieniu znajdziesz tutaj.

    Nie czekaj, bo jak zwykle schodzą szybko.

Check Engine

Yesterday I had exactly the same thing while driving to work at around -14°C; after connecting to the computer it showed the fault "P0101 - Leak in the intake manifold." After restarting the engine, everything worked properly. I also thought, as the guy above wrote, that something malfunctioned with the sensor in the intake.
 
I sprayed the connector with contact cleaner and for six years the problem hasn’t repeated itself.

How do you practically unplug this plug? Do we pull out the yellow pin a bit and then what? For me it’s seated on a rock, and I don’t want to yank the connector, because I might damage the socket where the MAP sits and there’ll be a real hole in the intake... :) Is there anything else to unplug?
 
You pull the pin back – all the way, then you have to squeeze the black plastic fairly hard; if the tooth still won’t release, you need to pry it with a small screwdriver. If you were removing the sensor to pull it out, don’t twist it sideways, or you’ll snap the locating pin. I’m just recalling from memory, if you can’t manage it I’ll check under my hood tomorrow.
 
You pull the pin back – all the way, then you have to squeeze the black plastic fairly hard; if the tooth still won’t release, you need to pry it with a small screwdriver. If you were removing the sensor to pull it out, don’t twist it sideways or you’ll break the locating pin. I’m just writing from memory, if you can’t manage it I’ll check under my hood tomorrow.

Thanks :) It came off without any problems, you do indeed have to squeeze hard, but once you squeeze it, it comes off without hesitation.
 
And everything is as clear as day. Just like the guys said - error P0101 - intake manifold leak. Cleaned the connector, we'll see if it returns. There was a Fiat ASO mechanic who tested all this for me, he also drives a T-jet and believes this is standard for these engines and in temperatures below -10°C
 
I'll dig into the topic a bit, but it probably doesn't make sense to start a new one, so to the point:
Giulietta 2015 MA 150hp
29,000 km on the odometer, oil changed every 10,000. In the last cold spells, at -14 degrees, one cylinder stopped working when I stood on red light for a longer moment (the engine was still cold), the 'tree' on the dashboard, start stop and DNA not working etc. In the morning, after the car sat in the sun for a while and warmed up, the error disappeared. After two days, when the temperature dropped again, the check engine appeared again, but with no other symptoms. Errors that appeared were:
P1022-17 - cylinder 2 uniair activation of the solenoid driver - circuit voltage above threshold
P0101-62 - blow-by in the intake manifold - signal comparable to fault
At the ASO they informed that most likely the MA module will need replacement. What do the guys think? I also noticed a minor thing: the turbo pressure gauge does not reach maximum on the scale, 2-3 bars below; in terms of driving I didn't notice a power drop.

Thanks for the help.
 
Do you have a warranty? Then replace it if they propose.
 
Julka probably doesn’t like frosts. First time during my usage it threw a tantrum on Tuesday at -15°C. It wouldn’t start and then threw a check engine. The next day when the frost eased everything was fine and it is fine to this day. Maybe this type does it... and Multiair doesn’t like frosts :)
 
Maybe you have a discharged battery?
 
And how did the story with this fault end for you?

- - - Updated - - -

Hello again. Yesterday, while driving calmly on the highway. Temperature gauge about 110. Not extreme. The check engine light came on. This morning I checked with a computer and it showed:
"-Signal from the actuator solenoids of uniair for cyl. 2
-intermittent"

Uni air is probably the electronic phase control system of the camshafts... hmm.
I cleared the fault and for now it's ok. But I'll drive it longer to be sure.

What do you think?

And how did the story with this fault end for you?

- - - Updated - - -

Momentary loss of electrical contact on the connector - nothing to worry about

And what if the fault appears every now and then? How to deal with it?
 
We have it in the family Giulietta 1.4 MA and I was told recently that a few times over 5 years of use it happened that the Check Engine lit up and Start & Stop activated, after which it could not be turned off. The user drives with Start & Stop off daily, so it surprised him even more that the Check Engine light appeared automatically and the Start-Stop indicator lit on the dashboard. The car has 70k km. It doesn’t use oil, fuel consumption normal, 7.2 average over the last 3000 km. While Check Engine lights up, from the user's reports it seems the engine isn’t changing its behavior compared to normal, only when starting downshifts the revs drop too low but you can drive and after accelerating it’s fine. The fault disappears on its own and nothing happens. In one situation Check Engine stayed on so long that they visited a service; the service removed the fault themselves. After connecting to the computer, the service technician said there were no other faults and now everything is fine. After the service, the problem appeared again but resolved itself while driving. I’m curious about the involvement of Start & Stop in this situation, which cannot be turned off from the dash if something in this regard is stuck. Recently we philosophized about what could have been, most likely the Start Stop sends some signal and the engine in this mode should shut off when the car stops, but it doesn’t, hence this anomaly. I test-driven the car, didn’t see concerning things. The engine is dynamic as at the start, the TCT gearbox works very well without signs of wear. In my drive, Check Engine and Start & Stop did not come on, the engine revs well, does not fluctuate etc. The only thing I noticed is that you can feel the engine running at idle in the steering wheel – it’s not diesel-like vibrations but bigger than in my 10-year-old Abarth and my new Alfa, indeed. Giulietta Veloce. The thing is, you can feel how the engine runs at idle sitting in the car, and before that you couldn’t. I don’t know if it has anything to do with this fault; maybe it’s just, for example, a mount, or maybe MA is misbehaving? The operating smoothness of this engine from the start hasn’t pleased me. Compared to the T-Jet, there’s a noticeable difference even considering that my Abarth has 130k km and almost 10 years. You know how it is in service shops, for them everything is always OK. meanwhile outside, as with the beginning, one of the valves ticks noticeably differently from the others but there is no progression of the problem and generally nothing happens, so it’s a bargaining chip for the service, that this type is like this and we won’t do anything. I’m now wondering only about this case that appeared a few times over these 5 years, could it be related to the MA system?
 
Last edited:
Regarding vibrations, unfortunately a frequent occurrence (later on, mirror vibrations are added) - fortunately the solution is simple - replace the engine mount under the reservoir of the fluid
 
We have it in the family Giulietta 1.4 MA and I was told recently that a few times over 5 years of use it happened that the Check Engine lit up and Start & Stop activated, after which it could not be turned off. The user drives with Start & Stop off daily, so it surprised him even more that the Check Engine fault appeared automatically and the Start-Stop indicator lit on the dashboard. The car has 70k km. It doesn’t use oil, fuel consumption normal, 7.2 average over the last 3000 km. While Check Engine lights up, from the user’s report it seems the engine does not change its operation compared with daily; only when starting, revs drop too low but you can drive and later when it accelerates it’s ok. The fault disappears by itself and nothing happens. In one situation Check Engine remained on so long that they visited a service, after which the service itself removed this fault. After connecting to the computer the technician stated that there were no other faults and now everything is ok. After visits to the service, the problem appeared again but resolved itself while driving. I’m wondering again about the Start & Stop involvement in this situation, which cannot be turned off from the dashboard if something in this regard is suspended. As we philosophized recently about what it could be, it most suggests to us that Start & Stop sends some signal and the engine in this mode should go out when the car stops but it does not, hence this anomaly. I drove the car, didn’t notice worrying things. The engine is dynamic as at the start, the TCT gearbox works very well without wear signs. During my drive Check Engine and Start & Stop did not light up, the engine revs well, does not fluctuate etc. The only thing I noticed is that you can feel the engine running at idle in the steering wheel – these aren’t diesel-like vibrations but larger than in my 10-year-old Abarth and in my admittedly new Alfa. Giulietta VeloceThe thing is that you can feel how the engine runs at idle when sitting in the car, and previously that wasn’t the case. I don’t know if it has anything to do with this fault, maybe it’s just the mount and maybe something is faulty? The operating quality of this engine has never felt right to me from the start. Compared to the T-Jet, there is a noticeable difference even considering that my Abarth has 130k km and almost 10 years. Do you know how it is in workshops for them everything is always OK. Meanwhile, outside, just as it was at the beginning, now one of the valves taps noticeably differently from the others, but you can’t see any progression of the problem and generally nothing happens, so it’s a bargaining card for the service, that this type behaves like this and we won’t do anything. I’m now wondering only about this case that appeared several times over these 5 years, whether it could be related to the MA system?
The battery probably needs recharging or even replacement
 
When connecting the charger, do I need to disconnect anything from the battery or do I just connect and charge?
In the Stilo I never disconnected anything and everything was OK, but the technologies used there were older.
So far with the battery everything is OK, but I’m asking for the future.
 
No need to disconnect when charging
 
As for the vibrations, unfortunately a common issue (later on the mirrors start vibrating too) - fortunately the fix is simple - replace the engine mount under the coolant reservoir

Can I somehow physically check this mount if it’s OK?
 
you can at most just see if there are oil leaks on the rubber seal, a more thorough diagnosis only after removing it—but if there is a leak it means it will get worse over time...
 
Last edited:
Back to the topic of the check engine. As I wrote it appears from time to time. I managed to record this situation. The computer signals that the Start&Stop system is unavailable and to check the engine. When the fault occurs there are stronger vibrations than usual. Most often after driving a certain distance the check engine disappears by itself and everything returns to normal. Then it’s normal for about two weeks. I’ll soon share a video with the fault.

- - - Updated - - -

I’ll upload a video when I’m back home, because the service centers are blocked at my work where I could share it and send a link.
 
Amortyzatory
Back
Top