• Jeśli chcesz dodać swojej Alfie charakteru i jednocześnie zaznaczyć przynależność do naszej społeczności – to dobry moment, żeby je zamówić.

    Ramki Alfaholicy

    Szczegóły, zdjęcia oraz informacje o zamówieniu znajdziesz tutaj.

    Nie czekaj, bo jak zwykle schodzą szybko.

yellow warning light

macki

New
Joined
Feb 23, 2011
Messages
29
Car
Alfa Giulietta 1,4 MA 170KM Black Etna
my yellow engine warning light came on at about 50 km/h, it stuttered for a few seconds and felt weak as if one of the cylinders had died or there was a fuel supply issue, but after a few seconds it returned to normal and drives normally. The problem is that the light is still on and neither Start&Stop nor DNA work. what could it be?
 
The computer won't be needed. Mate, a temporary loss of electrical contact on one of the engine harness connectors. Push all of them, disconnect the power cable from the battery (the one on the rapid connection) for 30 minutes and everything will return to normal (the fault will disappear). After reconnecting the battery you will only need to reprogram the power steering assist (turn the wheel from one extreme position to the other) and the window automation (open each window fully in turn, then raise them and hold the button for about 5 seconds)
 
Last edited:
my yellow engine warning light came on at about 50 km/h, it stuttered for a few seconds and felt weak as if one of the cylinders had died or there was a fuel supply issue, but after a few seconds it returned to normal and drives normally. The problem is that the light is still on and neither Start&Stop nor DNA work. what could it be?

If this starts to worsen or happens more often then it means the Uniar (Multiair) timing actuator is failing (a problem already known from other models with Multiair); bad news if your car is still under warranty. Misfiring, one cylinder not firing, fouled spark plug and engine jerking – that’s exactly the effect. Of course I hope it isn’t that...
 
Last edited:
Who knows this problem and in which models?

At most the angle position sensor could fail, cost about 50 euro
Don’t fantasize about what may pass and what may not. I’m writing about what actually failed in several cases (where the described symptoms were similar) and what was listed by several service centers in Poland, in mito,delcie and julce. Not a lot considering the number of cars based on the MA but it happens. In one of these cases I know the owner personally
 
If it starts to worsen or happens more often then it means the Uniar timing actuator is failing (problem already known from other models with Multiair),; costly if your car is under warranty. Misfiring, one cylinder not firing, fouled spark plug and engine jerking – that’s exactly the effect. Of course I hope that isn’t the case...

Part cost is about 2500. If the car is 3 or 4 years old, Fiat refunds about 90%. You need to negotiate well with the service manager. By the way – how do you know it’s that? Sent from my GT-N7000 using Tapatalk 2
 
Part cost is about 2500. If the car is 3 or 4 years old, Fiat refunds about 90%. You need to negotiate well with the service manager. By the way – how do you know it’s that?

I cannot be sure who had what fail, but if there is misfiring, cylinder problems (you can easily check by removing the plugs and seeing if any is flooded) and as a result the check light comes on, there’s a good chance, but exactly that must be confirmed by the service. As for costs, a full set (all parts + labor) is over 3k PLN, and don’t expect the FAP to refund you at 90%; I don’t know where you got such information. There’s a chance the best case they’ll only partially refund the cost of the parts (certainly not at the level you wrote) but labor will be fully paid by the customer. Best regards
 
Yes, you pay for labor, indeed. I have this from an ASO, during a discussion about my problem, which I’m writing about here. The Uniair module costs allegedly 2500. You can check in Eper.
 
Don’t fantasize about what can happen and what can’t. ...
Mate, you’re probably fantasizing - the problem generally doesn’t occur, because there would be talk about it not only on this forum. A single case can of course occur, and service shops gladly fix whole components under warranty, without looking into the cause of the fault - the pricier, the better. Generally, the thread author hasn’t spoken up, so he’s probably dealt with the problem himself. Misfiring in this case is more likely the result of improper action - after the check engine light comes on, the buddy should have immediately switched off the engine and restarted it, but he did revving.
 
Last edited:
Mate, you’re probably fantasizing - the problem generally doesn’t occur, because there would be talk about it not only on this forum.
Compared to you, I’m talking about authentic and concrete cases, also consider that not every Alfa owner has to belong to any forum or write about their repairs there! Don’t tell nonsense that the problem doesn’t exist because you know little about it.
A single case of course may occur, and service centers are happy to replace entire subsystems under warranty, not looking into what caused the fault - the more expensive, the better.
this is not a single case if there have already been several (i.e. fewer than 10) which does not mean the problem is widespread because I didn’t write anything like that
Generally the thread author isn’t replying, so he’s probably already dealt with the problem
would be nice if that were the case, although from the first symptoms to total failure may take some time, if it was really the actuator the problem would start occurring more often and intensify
Misfiring in this case is more likely the result of improper action - after the check engine light came on the buddy should have immediately turned off the engine and restarted it, and he was doing throttle blips
give it a rest and don’t sink yourself, first you wrote loss of contact at the plug, then about some pseudo sensor, now about inability to proceed (??) After all the person wrote clearly that it happened while driving, so it’s not his fault. At 50 km/h he should have immediately turned off the engine? Nonsense, sir ;)

- - - Updated - - -

You pay for the labor, indeed. Info I have from the ASO, when discussing my problem, which I wrote about here. The UniAir module supposedly costs 2500. It can be checked in the E-per.

the module itself 655 euros + some other small parts (gaskets etc) + labor = a bit over 3k (costs calculated by the ASO)
 
Compared to you I’m talking about authentic and concrete cases,.... stop it and don’t drag yourself down, first you write lack of contact at the connector, then about some pseudo sensor, now about inability to proceed (??) After all the person wrote clearly that it happened while driving so it’s not his fault. Driving at 50 km/h he should have immediately turned off the engine? You’re full of crap, sir ;)
I don’t doubt these are authentic cases you’ve only heard about... Re: the thread participant’s problem, he asked a specific question what to do for the light to go off and the car to regain technical functionality - instead of giving him that advice you’re spraying panicky talk about a hypothetical actuator failure (in it there could be a synchronizer sensor) - if you can’t help the buddy don’t scare him and don’t spread rumors. Probably the cause of the check light was a temporary loss of electrical contact by some engine harness connector (as I mentioned based on my experience with Alfa engines) - in that case you should stop and shut off the engine, then turn it back on, not continue driving (that was the buddy’s mistake). After restarting the engine runs smoothly but the check lamp remains + DNA inactive and S&S system - I WROTE EXACTLY WHAT THE BUDDY SHOULD DO TO RESTORE THE CAR TO NORMAL STATE. Of course the error can be read by plugging in a reader (it stays in the ECU memory), but you don’t need a computer for the car to start working normally. If someone in this situation on the road, I think this will help - I tested it myself and it works.
 
Last edited:
I don’t doubt these are authentic cases you’ve only heard about...
mate - you’re mistaken here, not only did I hear about them, there are some informations from ASO that did such repairs and in one case directly from the owner. I see your knowledge here is limited to what you can read on forums and you selectively pick what fits your theories or not, ignoring the given facts - a fundamental error
Returning to the buddy’s problem, he asked a concrete question what to do so the light goes off and the car regains technical functionality - instead of giving him that advice you’re spraying panicked talk about a hypothetical actuator failure (in it there could be a synchronizer sensor)
Hypothetical is exactly your own theory about a sensor that nobody has ever replaced because that’s not the problem, nor in any connector. Just because 5, 10 or 15 years ago that’s how faults were cleared doesn’t mean it still must be there, times have changed. They replace the whole module because it’s non-disassemblable. The buddy wrote about symptoms suggesting it could be what I’m talking about because the symptoms were identical. That’s what this forum is for, to share information, not to foretell using fates and connectors and sensors because maybe you had something in an Alfa somewhere)
- in that case you should stop and turn off the engine, then turn it back on, not continue driving.
and better to say 4 Hail Marys and spit 3 times over the left shoulder, then the fault will never happen again...

To avoid further debating on this topic, without reading errors there’s no point guessing and arguing. If it was a one-time and some random fault, after restarting the engine the light should go out. If it doesn’t go out and even disconnecting the battery for 15 minutes doesn’t help (or it lights up again after some time) then it probably won’t do without a visit to the service (or at least plugging into a computer)
 
Last edited:
Then you’re spraying panicked talk - the buddy asked a concrete question, did you give him an answer or did you start scare him with a serious fault? Disconnecting power for at least 30 minutes for MA engine to clear errors is a service procedure and I know about it from an ASO technician who did it for me. MA is not a diesel (where the check light goes off after 10 starts and/or driving 30–50 km); even if the cause of the error goes away, the check light won’t go out and the computer won’t exit safe mode on restart - the fault must be cleared and not necessarily as you can see you need a computer. You’re predicting the future from the tea leaves that’s you - pity you don’t tell the buddy to replace the whole engine but just the actuator. I described exactly the procedure to bring the engine out of fail-safe mode (I tested it myself) - that’s what the buddy asked. As for actuator repairs, Polish service centers had instructions that in case of any MA engine fault they would dismantle the whole assembly, replace with a new one, and send the damaged one to Italy - at first that’s what they did but that’s history now and concerned cars under warranty. The sensor that fails in the “non-disassemblable” actuator is number 2 on this diagram:
http://eper.fiatklubpolska.pl/navi?...SUBGROUP_7&SB_CODE=-1&WINDOW_ID=1&DRW_NUM=3|0
 
Last edited:
Maybe a small history of my case - not exactly identical to the initial topic (my issues started at 0 km/h), but having something in common, especially with the end of the discussion: AR Giulietta 1.4 MA mileage about 29,500 km, August 2012 (AC on), traffic in a jam (Zakopane), S&S off - standing between successive inclines (at idle) the car started shaking, yellow check engine light came on, almost no response to the accelerator. Turning off the engine and after a moment turning it on again - the engine runs fine, the light goes off.
Second time after a few days in a parking lot (after driving, at idle): again “delirium” - the engine shaking, this time the indicator did not light up, interior lights flickering and those visible when the doors are opened.
I managed to provoke such a situation before service (this time it was enough to drive with the “D” mode on and air conditioning on) - the car was handed for repair and during the inspection at 30,000 km a failed fourth cylinder ignition coil (misfiring).
After taking the car back (from the repair and after the inspection with replacement of spark plugs and oil) after about 20 km in the parking lot the misfiring on all cylinders returned!
Repair complaint - supposedly after swapping coil positions between cylinders 3 and 4 misfiring still occurred, suspicion of wiring harness problems (the harness itself wasn’t changed) ... The regulator replacement helped.
Finally, advice given to me when collecting the car after repair: when using the car mostly in the city and low annual mileage (below 10,000 km), change the engine oil every 12 months (which is also written in chapter 201 of the 02/2010 Edition of the user manual).
 
Last edited:
thanks for all the replies. I reported to the dealer, where I was told to wait an hour for the diagnosis itself. I decided to come the next day when I had more time. I got in, started it, and to my surprise I found that the light was not on. As if it really dies after about 10 starts. DNA and Stop&Start work. I should add that during these two days the car drove quite normally, problems did not repeat. In this situation I skipped the service visit the next day. I have no warranty since February, so any major repair would be expensive. I was also driving in D mode at that time, climate control is always on. It may not be related, but exceptionally I had cheap 95 octane fuel filled, which I decided to use up and now will switch to the most expensive branded fuels, as before.
 
because the yellow lamp lit up for the second time (this time without noticeable engine malfunctions) I went to read the codes and a MultiAir system fault appeared in one cylinder. Mechanics advised me not to do anything, because at most you can only replace the entire MultiAir block for 6000 PLN, and it’s not even certain that it will help. So I keep driving, and this time the light went out after a few kilometers.
 
Mate, as I already wrote, check the connectors and reset the fuel injector control unit - the problems should end.
 
because the yellow lamp lit up for the second time (this time without noticeable engine malfunctions) I went to read the codes and a MultiAir system fault appeared in one cylinder. Mechanics advised me not to do anything, because at most you can only replace the entire MultiAir block for 6000 PLN, and it’s not even certain that it will help. So I keep driving, and this time the light went out after a few kilometers.

well, that amount is probably made up out of thin air or simply multiplied by 2 ;) . There is nothing left for you to do but wait and observe what happens next. For me, from the first symptoms to total failure took 2–3 months, but that surely depends on many factors, especially monthly mileage of the car. I could describe the exact history of my case here (like colleague adamstrz) but for colleague Maciek-156 giving authentic service cases is just bluster and scary others with costs..., besides, I see that the person belongs to those who think that if this problem doesn’t concern them personally (or at least half the people on this forum) then it means the problem doesn’t exist. And the problem, though not widespread, does occur and if colleague still doesn’t believe, talk to the management who knows these cases well, but that’s aside. Returning to the topic, I’m a few days after actuator replacement because without it this wouldn’t be possible. No sensors, connectors, contacts, resets or other tricks help in this case. The fault in my car was mechanical; now I can only confirm that because I had the opportunity to see the damaged module later. After replacing the actuator, all earlier problems disappeared and the car runs like new. If anyone is interested in details, feel free to PM me.
 
Last edited:
Amortyzatory
Back
Top