• Jeśli chcesz dodać swojej Alfie charakteru i jednocześnie zaznaczyć przynależność do naszej społeczności – to dobry moment, żeby je zamówić.

    Ramki Alfaholicy

    Szczegóły, zdjęcia oraz informacje o zamówieniu znajdziesz tutaj.

    Nie czekaj, bo jak zwykle schodzą szybko.

Recoding lights to EU

rozewo

New
Joined
Aug 17, 2014
Messages
141
Car
Giulia
I invested in the multiecuscan program and an interface hoping that I would disable the side markers and make proper rear indicators. Unfortunately I don’t have such features there, I searched body computer, lights, I don’t see it.
The software costs 50 EUR.
Can someone help and possibly reprogram so I don’t buy unnecessary interfaces anymore
 
Last edited:
I invested in the multiecuscan program and an interface hoping that I would disable the side markers and make proper rear indicators. Unfortunately I don’t have such features there, I searched body computer, lights, I don’t see it.
The software costs 50 EUR.
Can someone help and possibly reprogram so I don’t buy unnecessary interfaces anymore

Search the forum, there’s quite a bit about it - but from what I read there, lamp replacement is the only option
 
The lamps are of course replaced with orange ones, it’s just that they flash with the brake light. This is split programmatically
 
I invested in the multiecuscan program and an interface hoping that I would disable the side markers and make proper rear indicators. Unfortunately I don’t have such features there, I searched body computer, lights, I don’t see it.
The software costs 50 EUR.
Can someone help and possibly reprogram so I don’t buy unnecessary interfaces anymore

the cost 50 euro relative to the car is probably small. Share where you’re from.
 
My colleague has a free program so he won’t do it.

- - - Updated - - -



That’s a bit of a drive to Białystok, so it’s cheaper to spend 50 euro.

From what I understand, he already bought MES, just didn’t find the option for what he wants to change.
 
And we have a problem. Indeed I managed to disable the indicators and the side lights, but I couldn’t calibrate the proxi, and now I have a blinking odometer and a check engine. The elm interface also stopped responding.

Year of production 2017

Can the elm327 be disconnected with ignition on? because a change of interface end was required during calibration? after connecting the blue then gray nothing else worked.
The interface also hasn’t connected to the computer since then.
 
Last edited:
Can the elm327 be disconnected with ignition on? because a change of interface ends was required during calibration?
2 x YES, for safety you could have checked the adapters’ operation earlier by connecting to modules that require them (ABS, air conditioning).

Can the elm327 be disconnected with ignition on? because a change of interface ends was required during calibration? after connecting the blue then gray nothing else worked.
The interface hasn’t connected to the computer since then.
And do you have the interface properly set in the program (ELM Highspeed)? Maybe it just died.
 
The elm interface also stopped responding.
did Windows not override your driver (I understand USB and these are clones of USB-serial Prolific or FTDI)? check in the port properties where it was installed (Device Manager -> COM Ports) the driver date. Counterfeits work but with drivers from e.g. 2008-2010 and such sellers include them. Unfortunately Windows Update likes to replace them and they can detect counterfeits in some way.

haven’t you plugged into another USB? sometimes the COM port number changes.

do you have adapters to do proxi (gray/blue)?
 
The battery died during the upload. Recharging, redoing the proxi procedure and for now ABS and traction control did not pass and it still shows check. We’ll drive it because to clear ABS you have to drive a bit. And I’ll repeat the procedure.
 
if it didn’t pass, you do it again - proxi has to pass and that’s it, driving around won’t help.
 
download Multiecuscan 4.7 and do proxi. in version 4.7R1 proxi for ABS doesn’t work
 
did something break in R1? from the standard MES version descriptions, R1 just fixes mixed adapter assignments with 4.7 (maybe not for Giulias?). I’m using R1 but Multiplexed and it works, though I have a feeling with each new version it crashes more often and proxi after 2-3 repeats on some cars. Recently proxi passed according to MES but the odometer started blinking, radar dropped out. In another car PAM, in both cases after 2-3 consecutive reruns proxi was OK. A few days later, I did 2 Giulias 2017 and 2019 and both passed without a hiccup. No rules.
 
Amortyzatory
Back
Top