• Jeśli chcesz dodać swojej Alfie charakteru i jednocześnie zaznaczyć przynależność do naszej społeczności – to dobry moment, żeby je zamówić.

    Ramki Alfaholicy

    Szczegóły, zdjęcia oraz informacje o zamówieniu znajdziesz tutaj.

    Nie czekaj, bo jak zwykle schodzą szybko.

Problem with the Key (central locking)

wojtasch

New
Joined
Jul 31, 2016
Messages
23
Car
Alfa romeo Giulietta 2012r 1.4 tb 170km
Hello
while going out of town, the key got soaked. After shaking out the multitool, Dzunia opened up and fired normally. I drove home and opened it – it was wet, so I cleaned it, dried it, and replaced the batteries with a new one. The problem is that opening the central locking (lock, unlock, and the trunk) now works from a very close distance (i.e., right at the front windshield). It starts up normally, so the immobilizer is ok. Has anyone encountered this – is the key damaged and should I order a new one (the spare central locking controller works normally) or has it somehow decoded and that’s why it behaves like this? The dealership will probably suggest a new key, and maybe I won’t even have to go there.
P.S. – the key being disconnected from the battery lasted about 2 hours – maybe that’s the issue
Thanks for any hints
 
If it had decoded, it wouldn’t work at all. Wash it with petrol or some IPA and dry well with a hair dryer; there must still be moisture somewhere or you damaged something during cleaning. Look under a magnifier to see if all the SMD components are in place, something might have fallen off. Swap the batteries with the spare (or measure the voltage) because maybe the new one is some crap
 
Last edited:
Hello again
The key dried with a hair dryer, sprayed with degreaser and finally with electronics cleaner. Along the way I replaced yet another third battery to eliminate too low voltage. No effect....
Do you guys have any ideas or should I go to the Aso for a new key???
pz
 
it looks to me like some mechanical damage to the board or one of the components. If you pulled the batteries right after submersion water could not have damaged anything and after drying it should work. Where are you from?
 
That’s what comes to mind, check the electronics and especially anything that is the antenna – I’m afraid of corrosion there.
 
if I send a photo, will you be able to locate the antenna or the component that it corresponds to?
 
Key is functionally OK, I didn’t take mine apart and I don’t know what’s inside, I suggest taking it apart down to the board and carefully inspecting + cleaning, or giving it to a savvy electronics friend for a go :)
 
remote opened up, cleaned, degreased, contact sprayed and dried. I’ll hand it to a savvy friend for a play...... cheers
 
- photo of the key, I have the same problems and I’m not really sure where the antenna is.
 

Attachments

  • key-2 018.JPG
    key-2 018.JPG
    90.6 KB · Views: 24
The central locking antenna is burned out. You can see it, it runs along the right edge. The remote looks very similar to Fiats. I wonder if they fit interchangeably - I haven’t tested. At my mate wojtasch I would move the PCF onto a working board and see how it works. Probably helps.
 
20160808_160336.jpg20160808_160419.jpg

photos of my board - maybe someone can locate the antenna or the element that is responsible for signal amplification?

- - - Updated - - -

:)"I would move the PCF onto a working board" - I’m not really sure what that means - please explain - maybe it will help:)
 
PCF7946 is the biggest IC, it handles immobilizer and central locking.

The other components (except for the buttons, a few capacitors and the coil for immobilizer) are the entire RF path of the central locking.

Your board is identical to Ducato/Bravo production by Magneti Marelli (there are also Delphi ones).

The antenna is marked in red. If you want to tinker, swap components at the start and end of it.20160808_160336.jpg
 
Last edited:
In the bottom photo you can see two awkward through-holes; it’s worth checking if they have contact top to bottom.
 
indeed, upon closer look those two through-holes are not great, I’ll try at work on a soldering station to fix them - because my iron will just mess it up... If it doesn’t help I’ll follow small_777’s advice and play with the antenna
I’ll share results later. cheers
 
In the bottom photo you can see two awkward through-holes; it’s worth checking if they have contact top to bottom.

I measured it....... something is wrong with the top one - it has no contact with the Battery terminal - I’ll fix the soldering
 
Into such a through-hole you insert a thin wire like kynar and solder on both sides.
 
Amortyzatory
Back
Top