• Jeśli chcesz dodać swojej Alfie charakteru i jednocześnie zaznaczyć przynależność do naszej społeczności – to dobry moment, żeby je zamówić.

    Ramki Alfaholicy

    Szczegóły, zdjęcia oraz informacje o zamówieniu znajdziesz tutaj.

    Nie czekaj, bo jak zwykle schodzą szybko.

Problem with the driver's window

Red_Sebald

Member
Joined
Feb 10, 2023
Messages
54
Location
Warszawa
Car
Stelvio 2.0 200KM Q4 2018
Good morning, I’m asking for advice ;) Specifically, in my Stelvio ('18) for a long time there’s a problem with closing the window on the driver’s side. After opening (not fully), when trying to close the window, it rises a little and then starts to go down. And after a few attempts it reaches almost full opening, then on the next attempt it politely closes. Honestly, I’ve missed this during the last inspections and didn’t report it to the dealership, but recently, during heavy rain, the problem turned out to be significant. Has anyone else had similar issues? I’ll add that we’ve had the car in the family since the beginning, it hasn’t had any incidents, the door trim hasn’t been touched, etc.
 
I think you’ll have to remove the trim and inspect what’s going on with this drive. Apparently the window is slipping because the mechanism detects increased resistance and lowers a few cm after that (as if someone cut you like Wisły in Killer). It’s strange though because it should probably work from full as well. Buy the trim clips in the original, aftermarket ones are cheap but rubbish. Because during removal some of them will probably crack. You can try warming the trim around first, supposedly when warm they become more flexible and you can detach without damage. And a sturdy metal trim pry tool, plastic ones are lethal in this case.
 
Thanks, I also think the anti-squeeze protection is working. For now I’ll deal with it, because knowing my manual skills I’d end up with a poorly fitted and squeaky trim, and that would annoy me more than the wild window :)
 
Yeah, it won’t drop from full because there’s nowhere lower to go, I must have been tired :-).
Try if you want to tilt it to halfway, then with one hand pull the window up and with the other press the button. That is, assist the motor. If it goes normally then the protection is 100%. I suspect someone dismantled it and messed something up or there’s dirt on the guides, something got in and blocks it.
Dismantling isn’t that hard and this car squeaks with every plastic like some old junk. The quality of plastics is tragic. I doubt you could make things worse.
 
I’ll check the dirt hypothesis, thanks. Probably no one tinkered with it – the car has been in the family from the start and I don’t recall us commissioning anything to do with the doors – unless the dealership did something on its own and forgot to inform :)
I started with cars from the PRL so maybe I have lower expectations but the quality of materials and fitment isn’t that tragic. Sometimes I hear crickets but there’s no drama.
 
I’ve had that too with 125/126/Poldek/Łada... now again Fiat 'premium'.
In general I’m just comparing with other today’s and much cheaper cars. Here most of the plastics you press creak like crazy. The center console (where the USB/ cig lighter), the tunnel, the top light, or the dashboard with the gauges as a whole. As a result you get rattles and squeaks at slow speeds or on bumps, also during braking/acceleration as tensions change for a moment. Turn off the radio and you’ll see :-). And sit in any Toyota and you’ll see a gulf in that regard (perhaps the only one).
Regarding the factory fit of both my left doors, I’ve written about it somewhere before – shame as a hat. Fortunately I managed to sort it out (myself) in terms of adjustment.
 
Interesting, with me basically nothing creaks. Sometimes something vibrates on uneven surfaces, but I suspect the camera. Maybe Giulia it goes together better, or it’s in Italian – sometimes it wanted, sometimes siesta.
 
Perhaps a matter of year and different plastics. Or as you say Giulia-Stelvio they have it differently. I have the impression that the plastics are some crappy stuff and creak when they rub against each other, and if you wedge between them a piece of EPDM foam (to separate) they quiet down. On the corners you have vents. If you press them with your hand (as if you wanted to flatten the perimeter) does nothing? Mine also creak badly.
 
I’m not complaining about squeaks in my Giulietta from late 2021, but I don’t know if that matters; it’s really well assembled. The only very small squeaks appear on cold days over paving stones and come from the glovebox lid in front of the passenger seat (I need to check if it can be adjusted). And sometimes from the front pillars when one wheel hits a curb while entering—suspect something went wrong when they installed the alarm sensors at the dealership. Compared to the 159 it’s noticeably better. Practically on par with Volvo (though the plastics are of a higher grade there). BUT when they gave me one time for 2 hours during a service that squeaked, but it was a quite worn example with over 150k km… And it seemed someone had oiled the dashboard with some compound, then I assumed that the compound caused some friction... These circular vents — indeed if I cut them, bend them, I’ll hear light squeaks — but e.g. in the Volvo mentioned the squeaks when pressing on components are louder...VeloceNo, I don’t complain about creaks in my Giulietta from the end of 21 (and I’m not sure if that matters), it’s really well assembled.. The only very small creaks appear on cold days over the paving stones and come from the glove compartment lid in front of the passenger seat (I need to check if it can be adjusted). And sometimes from the front pillars when entering with one wheel onto the curb - I suspect they screwed up something when they installed the alarm sensors at the dealership.. Compared to the 159 it’s noticeably better. It’s practically on par with Volvo (though the plastics there are of a higher quality).
BUT when they gave me Stelvio for 2 hours during a service, it did creak indeed, but that was a rather worn example with mileage >150k... And it seemed like someone had smeared the dashboard with some preparation, then I concluded that that preparation caused some friction... Those round air vents — indeed if I cut them, bend them, I’ll hear light creaks — but e.g. in the mentioned Volvo the creaks when pressing on the elements are louder..
 
I’m not one of those who go around poking at everything looking for faults; I mostly pay attention to what’s visible or shows up during normal use — and the Juke is perfectly fine. I left Mercedes or BMW rather disgusted.
 
Well I don’t poke around for no reason either. Only when it squeaks in general I try to find what mainly causes it.
 
Well I must admit that if it doesn’t squeak, I don’t poke around :) But seriously, at least in my example the fit is OK. Especially compared to my previous Outlander, where the door trim visibly bulged when the window was opened. The X-trail also squeaked pleasantly. I haven’t had Toyotas yet, the road is still ahead for me :)
 
Maybe only this one I have (actually my wife has it) is as well-made as yours Alfa :⁠-⁠).
 
Amortyzatory
Back
Top