• Jeśli chcesz dodać swojej Alfie charakteru i jednocześnie zaznaczyć przynależność do naszej społeczności – to dobry moment, żeby je zamówić.

    Ramki Alfaholicy

    Szczegóły, zdjęcia oraz informacje o zamówieniu znajdziesz tutaj.

    Nie czekaj, bo jak zwykle schodzą szybko.

Problem with the boost

menda96

New
Joined
Jul 31, 2018
Messages
82
Car
Alfa Romeo Giulietta 1.4 MultiAir Turbo 170KM 2010
Hello, I have a problem with boost on a GT1446 hybrid. The turbine is oversized and the compressor wheel is made of forged aluminum. It starts up very well, etc. But the problem is that the program is set to 1.7 bar while the map sensor reads 1.3 and it does not produce the power it should; output is 225 hp and 340 Nm. The question is whether it's possible that the blow-off or something else is venting early, or is that unlikely and there is a leak? I should add that during acceleration you can hear something releasing or pressure escaping. I already asked in another thread but no one gave a sensible answer.
 
menda96
If you really have such a pressure set and the fuel system is tuned to that pressure in the ECU software and your turbine is technically capable of generating that pressure, then you have a few possibilities.
Factory DV/recirculation valve may not hold that pressure anymore /something new/
Wastegate may be poorly adjusted or already worn out.
I’m skipping the intake
You can check this at home with a few tests.
Another possibility is sensors not reading such pressure.
Check their specifications by part numbers or provide the pressure 2 bar for these sensors from a pump and see what the ECU shows.
They described this problem in modified Punciak/ the weakest version.
 
Last edited:
the turbine was done a month ago, so the WG certainly is not worn out
 
The rod is adjusted as it was stock, or at least that's what the guy who did it told me. Shortening the rod generally does nothing and lengthening worsens the effect. I should add that I have the strongest version, 170 HP. Today the mechanic also mentioned the DV to me.
 
What to do when the stock DV no longer holds pressure? I mean, not at all holds even when it's functioning?
 
replace it, because it probably doesn't fit with the rest of the engine work.
 
Last edited:
More power because if you’re supposed to have 1.7 and it bleeps, that means it can’t handle it and for it that’s already a big deal.
Stock is already starting to bleed around 1 bar.
 
[

I see on the net that often they block the DV and there are ready-made blocks for it. What is the purpose of this?

- - - Updated - - -

More power because if you’re supposed to have 1.7 and it bleeps, that means it can’t handle it and for it that’s already a big deal.

Stock around 1 bar starts to bleed.

Apparently the stock pressure is about 1.5 bar, so how could the stock one bleed with so little? If more power, then which exactly, because looking on the net nothing is shown about this?
 
Last edited:
menda96
If you really have such a target pressure set and the fueling system is tuned to that pressure in the ECU software and your turbo is technically capable of generating that pressure, then you have a few possibilities.
The factory DV no longer holds that pressure / nothing new /
The WG (wastegate) has the rod misadjusted or is already fatigued.
I’m skipping the intake.
You can check this at home with a few tests.
Another possibility is sensors don’t see such pressure.
Check their specifications by part numbers or provide the pressure 2 bars for these sensors, e.g., from a pump and see what the ECU shows.
They described this problem in modified Punciakas / the weakest versions /
I bought a blank for the turbine and removed the DV; probably now the car has gone into limp mode and holds 0.5 bar. Any ideas what to do?
 
Take a photo of this DV that you removed.
Were cables connected to it?
Take a photo of the engine, more on the right side so you can see the throttle body and engine cover.
Because I see it seems you didn’t do it correctly.
 
Take a photo of this DV that you removed.
Were cables connected to it?
Take a photo of the engine, more on the right side so you can see the throttle and engine cover.
Because I see it seems you didn’t do it correctly.

IMG_20191004_121059.jpg

So I removed it from the turbo and put a block in. I’ll take a photo of the engine after 14:00 because I’m at work :(. And there, of course, the cable is connected.
 
Did you previously have an IHI turbo?
Is the DV from IHI blocked or just the hose unplugged and extended to the DV at the gate?
 
Did you previously have an IHI turbo?
Is the DV from IHI blocked or just the hose unplugged and extended to the DV at the gate?

I had a Garetta because it was a 170 HP version and I made a hybrid out of it. So this is the stock DV.
 
Aha.
Buy it from the link and you’ll have a DV that holds pressure. [emoji817] And now install it as it was and don’t forget to connect the cable.
 
Amortyzatory
Back
Top