• Jeśli chcesz dodać swojej Alfie charakteru i jednocześnie zaznaczyć przynależność do naszej społeczności – to dobry moment, żeby je zamówić.

    Ramki Alfaholicy

    Szczegóły, zdjęcia oraz informacje o zamówieniu znajdziesz tutaj.

    Nie czekaj, bo jak zwykle schodzą szybko.

[Giulietta] Operational tips

Thanks, that’s probably it. Any idea where to buy it besides the official dealer? Edit: the part number matches. At the dealer they want 438 PLN for the buckle.
 
Last edited:
Hi. I have the opportunity to buy a Giulietta QV at a quite attractive price, but in the near future the suspension, bushings, wheel bearings, discs, pads and the drivetrain (CV joints, half-shafts, driveshaft) will surely need replacing as well. Could anyone at least roughly estimate what the costs might be? Of course with proper parts, because if you do it, you do it properly.
 
Hi. I have the opportunity to buy a Giulietta QV at a quite attractive price, but in the near future the suspension, bushings, wheel bearings, discs, pads and the drivetrain (CV joints, half-shafts, driveshaft) will surely need replacing as well. Could anyone at least roughly estimate what the costs might be? Of course with proper parts, because if you do it, you do it properly.

Rear suspension: only the dealer for the rear, with the front it’s well over 3.5k, you’d have to call and ask current prices; Bushings are higher, if you replace just bushings without the struts you’ll have around 2k for parts and labor; Discs + pads – discs only OE, the rest warps but they’re cheap – around 1.5k for the set, parts and labor; Drivetrain – half-shafts about 1k+ for replacements, joints 600-800 PLN, and hubs about 1k for SKF; worth asking the dealer as well. Also labor. I recommend a thorough check of the rest, because if there are such deficiencies in servicing, soon the timing belts/variators may need replacement, turbo with wiring since oil is changed every 30k km, maybe a separator; these parts currently cost a lot, everything counted in thousands.
 
Last edited:
in other words, a worn-out junker, someone’s getting rid of it because they know it will be a lot to bring back to a good state.
 
in other words, a worn-out junker, someone’s getting rid of it because they know it will be a lot to bring back to a good state.
It depends on how cheap that purchase price is.
 
Once again I turn to the forum brothers for help. Maybe a electrician/engineer will read this. Our Giulietta The repair was undergoing, it was unplugged from the battery for about a month. In the meantime, because two bolts on the front rails broke, the only method was to weld nuts and unscrew them. The operation succeeded but after reassembling everything a disaster occurred. MES in full version does not connect to the engine control unit, the car won’t start, there are engine control unit errors and probably ABS pump errors. And from the car’s level information about unavailability of start&stop (probably immobilizer), the fuel pump is not audible. I guess something burned during welding. What to do in such a case and does the ECU have any protection such as a fuse that needs checking? Thanks in advance for any advice
 
Rear suspension arms - only at a dealership, together with the front ones it’s well over 3.5k, you’d have to call around to see what it costs at the moment
Bushings - are higher up; if you replace only the bushings without the control arms, it’s around P+T 2k
Discs + pads - discs only OE, the rest wears unevenly but they’re cheap around 1.5k for a full set P+T
Drivetrain - CV joints are about 1k+ for replacements, joints 600-800 PLN, and hubs around 1k for SKF; also worth asking the ASO

On top of that the work
I recommend a thorough check of the rest of the stuff, because if there are such deficiencies in servicing, soon the timing belts might need replacing, turbo with wiring work because oil is changed every 30k km, maybe a separator, these parts currently cost a sack of money, everything is counted in thousands

Thanks for the answer and information! It turned out there isn’t as much of a disaster as it seemed and the things that needed dealing with were typical consumables. After checking the whole car, it appears it’s not neglected. In the start there was a bit to top up, but in the end I heard that I should drive, take care, and remember to do everything on time and it will serve without problems.
 
Planning to buy a Giulietta QV with 185k km. It has been done up to 300 km (big IC, downpipe, exhaust, bigger turbo). What should I look for when buying? Is it worth it at all? I’ve heard there are problems with spare parts and that they’re expensive. Please share your opinions :)
 
Once again I turn to the forum brothers for help. Maybe a electrician/electronics read this. Our Giulietta The car was in restoration, was unplugged from the battery for about a month. In the meantime, because two bolts on the front rails broke, the only method was to weld nuts and unscrew them. The operation succeeded but after reassembling everything a disaster occurred. MES in full version does not connect to the engine control unit, the car won’t start, there are engine control unit errors and probably ABS pump errors. And from the car’s level information about unavailability of start&stop (probably immobilizer), you can’t hear the fuel pump. I suspect something burned during welding. What to do in such a case and does the ECU have any protection such as, for example, a fuse that needs to be checked? Thanks in advance for any advice

I can already answer myself. It turned out that the processor in the engine control unit and the ABS control unit were damaged. The engine control unit was repaired and I bought a complete ABS pump from a listing and replaced the control unit myself. The car came back to life. And because I let myself be tricked by using some anti-short-circuit device during welding, which did nothing, I lost about 1000 PLN from my wallet. The loss is bigger because Julka had its power programmatically raised which, due to the processor replacement (data could not be recovered), vanished. But of course the guy who repaired it can do it again for 900 PLN ;)
 
Hello. I’m a new owner of a Giulietta 1.4 120HP TB from 2011. I plan to replace the timing belt, idler pulley, and belt kit. Will these parts be OK?
Timing belt DAYCO 94709
Timing belt kit tensioner INA 531 0414 30
Water pump ASHIKA 35-00-015
Crankshaft pulley DPV1021
Multi-rib belt kit INA 529 0013 10
Thanks in advance for the help.
 
What brand of oil filters do you use for the 1.4 MA? OE makes Clean Filter for about 40 PLN. The same but without Alfa Romeo logo ML1708 costs about 15 PLN. Has anyone bought this filter? Or do you prefer Filtron, UFI, Mann and others?
 
Do you have someone who can do DP for 1.75tbi remotely? Most companies want to do it on the car, but I found only those within about 300 km.
I searched the internet and there’s only Ragazzon. I’m looking for other options.
If it’s on the car, best around Poznań area.
 
Hello. Is anyone from Lublin with a program for Alfa to reset the service? (Periodic service). Or suggest a program to download somehow via OBD... Regards. Kasia
 
Last edited:
That’s what a xenon burner looks like after 12 years and 178 thousand. The brightness at this moment is comparable at best to better H7s, but the color temperature is completely fading, e.g. on wet pavement.
You can wait until they completely fail, but after replacing with new, you immediately see what you were losing.

IMG_1510.jpg
 

Related threads

Amortyzatory
Back
Top