• Jeśli chcesz dodać swojej Alfie charakteru i jednocześnie zaznaczyć przynależność do naszej społeczności – to dobry moment, żeby je zamówić.

    Ramki Alfaholicy

    Szczegóły, zdjęcia oraz informacje o zamówieniu znajdziesz tutaj.

    Nie czekaj, bo jak zwykle schodzą szybko.

Multifunction steering wheel installation

pumba

New
Joined
Aug 1, 2011
Messages
16
Car
159 2,4 jtdm sportwagon
Hello
Such a question: is it possible to install a multifunction steering wheel on a 159 model if it didn’t come with one in the standard equipment?
Maybe someone has already taken this route.
 
And could you elaborate the topic because I don’t know what it’s about?
 
Proxy Alignment is the so-called proxy alignment (at least that's how they say it in Poland). The idea is that the body computer in the car is each time adjusted to its factory equipment. Adding some other equipment to the car, for example a multifunction steering wheel in a case where it wasn’t planned by the factory, requires "adjusting" the onboard computer to the new situation. This can be done, for example, using the FES program and an ELM327 cable, which gives access to CAN. In the case of a multifunction steering wheel I still wonder... whether versions that didn’t have this feature will have the proper connector and plugs brought out? As is known, these buttons on the steering wheel must be connected to the radio.
 
the title cannot be changed but here at the top it’s corrected (forum hole??) :]

All right, I’ll take the wheel apart and see if there are any free connectors, I’m afraid there won’t be due to cost-saving. but I’ll write something once I take it apart, for now thanks for the information
 
Check also whether after removing the radio you have the proper harness to plug in! Disassembling the steering wheel isn’t that simple, but if you search the forum you’ll find an instruction on how to do it.
 
Tell me, does a multifunction steering wheel differ in its construction besides having buttons, or is it the same?
In other words, for a steering wheel that didn’t have buttons, can they be retrofitted along with the trim on a plug&play basis, or is e.g. the steering wheel mount different?
Regards.
- Rafał
 
So I checked on my car and unfortunately it’s similar to the 156, i.e. replacing the tape, the silver cover on the steering wheel (not the whole wheel), purchasing the buttons, replacing the steering wheel harness (the one from the tape to the airbag, horn and the relevant buttons) I don’t know what else needs to be changed from the tape towards the radio or I don’t know where (unfortunately I don’t have the 159 schematics yet).
If any of you have good PDFs, I would greatly appreciate them
 
Thanks, interside. What else is needed, I don’t know, because I have multifunction already, I just wanted to know whether the steering wheels themselves differ in any way…
Regards.
- Rafał
 
the steering wheel can be replaced, there must be the equipment version, preferably where there is already a factory loom to connect the buttons, a proxy alignment is necessary afterwards because the speedometer flashes - the buttons for call handling do not work but the rest of the buttons work (based on my experience from a previous car).
 
Unfortunately for me there are looms without wires leading to the buttons, so replacing harnesses together with the tape, I’ll probably pass because it would be too expensive for me, especially since I bought it with a non-original radio and I have a Pioneer AVIC D3 and an interface is required, so I give up. maybe in the next one it will be standard :).
 
I installed almost plug&play steering wheel radio control. It seems to depend on the equipment version of the car. Fortunately in my case all looms were present. Proxy alignment didn’t have to be done. However there was no wiring for the cruise control… and it had to be pulled separately. I wonder if in your case by changing the steering wheel it would solve the issue... on Allegro you can get multimedia versions in good condition quite cheap already for about 150 PLN… of course provided the color is black.
 
Last edited:
A small tutorial on where and how, I described the procedure for removing the airbag when changing stalks (topic: steering wheel replacement) but I repeat:
Disconnect the battery - to avoid steering lock the key must be in the ignition, then we can turn the steering wheel freely
1. Unscrew the lower steering wheel housing with 4 hex screws from the bottom, remove the connector under the steering wheel which has special grounding connectors for the airbag
2. Remove the airbag - rotate the steering wheel 90° and insert a flat screwdriver from the bottom into the rear wheel opening (as in the picture) firmly twist the screwdriver, the airbag will pop off, then rotate the steering wheel so you have access to the second opening and again do the action with the screwdriver, note it’s not easy, the latch is big and strong but if you twist hard it will work. Please don’t be discouraged after the first failed attempt. I discovered that pressing doesn’t work better, turn instead


3. Unplug the cables from the airbag
4. Unscrew the cross-head screw cover as in the photo
IMG-20120724-00111.jpg
Do everything with the steering wheel installed, so the holes are at the back :)
5. Remove the cover
6. Unscrew the screws securing the horn ring - Torx key
IMG-20120724-00106.jpg
7. Gently remove the ring because there are springs and flat connectors for the horn that can be lost - we insert the loom with the connector for the multifunction buttons
IMG-20120724-00107.jpg
route the harness for the buttons under the ring so it doesn’t obstruct pressing the horn

7. Put the cover with the buttons back on - tighten the screws - reconnect the battery - Proxy alignment and everything works
IMG-20120724-00109.jpg

The operation takes about 30 minutes; I recommend buying the whole steering wheel to have the loom with the extra wires for the buttons

Works in every version, it must because I have the Italian BASIC version which had nothing
 
Last edited:
Tell me, if I have a multifunction steering wheel in a 159 and replace it with one without buttons, but transplant the button-equipped trim onto it, will I run out of any wires and can everything be connected, or is the trim alone not enough because the wheel also has to be multifunctional?
Regards.
- Rafał
 
And I have a question what is this Proxy alignment, I replaced in 156 and didn’t do anything, such a thing, does it have to be done?
 
Tell me, if I have a multifunction steering wheel in a 159 and replace it with one without buttons, but transplant the button-equipped trim onto it, will I run out of any wires and can everything be connected, or is the trim alone not enough because the wheel also has to be multifunctional?
Regards.
- Rafał
It depends; you must check if you have these wires because as you can see some cars have them and others don’t; unfortunately I have this variant where you have to replace the tape.
 
Amortyzatory
Back
Top