• Jeśli chcesz dodać swojej Alfie charakteru i jednocześnie zaznaczyć przynależność do naszej społeczności – to dobry moment, żeby je zamówić.

    Ramki Alfaholicy

    Szczegóły, zdjęcia oraz informacje o zamówieniu znajdziesz tutaj.

    Nie czekaj, bo jak zwykle schodzą szybko.

MES logs - request for analysis

Roman35

BANNED
Joined
Sep 28, 2014
Messages
652
Car
Giulietta 150 KM 2016
Hello,

I would like an analysis of the logs made in MES. The problem I have is that after temperatures dropped, the issue with jerking when starting has returned (even though after the repair in spring, to a lesser extent than a year ago). Additionally, during acceleration the RPMs slightly fluctuate, especially in third gear. I also have a comparison with a tow car and the difference is as if they were two different engines.

I am posting two tests:
First: as advised by a colleague piotriix, I did a test – pedal to the floor and up to 5,000 RPM (in the logs from 130 seconds).
Second: normal driving in traffic:
Here also a dyno chart:

https://onedrive.live.com/redir?resid=7EFF12D0AAAF0B65!128&authkey=!AI5zCE4YAk7vVA8&ithint=file,csv

Second: normal driving in traffic:
https://onedrive.live.com/redir?resid=7EFF12D0AAAF0B65!127&authkey=!ABZw67oMwfryVFY&ithint=file,csv

Here is also a dyno chart:
https://onedrive.live.com/redir?res...authkey=!APXxnybeIvLbdRQ&v=3&ithint=photo,jpg
 
- the lambda sensor after the catalyator is functioning correctly.
 

Attachments

  • G-sonda1.jpg
    G-sonda1.jpg
    101 KB · Views: 109
But in front of the catalytic converter it lies on the ground.
And as for the one behind the cat, it seems to me that it’s running too lean. I don’t know but in my Julka this correction is minimal as well in the 147 it was small. This one here behaves typcially for a sensor before the cat. Maybe MA handles it differently
 
But in front of the catalyst it lies on the ground.
- another possibility is that MES does not support this, because this is a current sensor, not voltage like the one after the catalytic converter.
- waiting for someone to make similar logs in MA.
- a question: were the logs taken in N mode, or D (dynamic)?
- regarding the plot progression, the colleague measured too many parameters, hence the graphs refresh too slowly and the plot is jagged.
 
Last edited:
I will write to Yaniego and ask about the MA sensor support.
 
- another possibility is that MES does not support this, because this is a current sensor, not voltage like the one after the catalytic converter.
- waiting for someone to make similar logs in MA.
- a question: were the logs taken in N mode, or D (dynamic)?
- regarding the plot progression, the colleague measured too many parameters, hence the graphs refresh too slowly and the graph is sharp.

Logs were made in N mode. I’m not complaining about D specifically.
I can always log fewer parameters if it helps.
 
- a few plots from the OBD test and city driving.
- Scan XL Pro program, parameters on the plot refresh every 200 ms.
- OBD test plot made with a scale of 10 and 100 on the plot.
- city driving with a scale of 100.

p.s.
- for comparison, a plot from idle lambda sensor with GT-JTS, there seem to be two current sensors before the catalytic converter and one after the catalytic converter.
 

Attachments

  • G-Ma scanxl1.jpg
    G-Ma scanxl1.jpg
    91.7 KB · Views: 71
  • G-Ma scanxl2.jpg
    G-Ma scanxl2.jpg
    93.5 KB · Views: 64
  • G-ma scanxl-miasto.jpg
    G-ma scanxl-miasto.jpg
    97 KB · Views: 63
  • GT-JTS3.jpg
    GT-JTS3.jpg
    131.3 KB · Views: 82
Last edited:
A colleague wrote that one sensor was already replaced by 10k km because it was faulty, question why, defect or something fried it.
Since they replaced half the engine and part of the electronics, flashed different software, but the effect isn’t there, so what?
Fuel pump? Injectors? Or does this model behave like this :mad:
I think it’s high time to go to someone who truly knows these engines because the service messed up, and all along the line.
 
Last edited:
Well, there is an improvement after the repair, I won’t lie, it occurs only to a lesser extent than before. When it’s 10°C outside it’s even perfect.
And the difference is that earlier it happened for 5-10 minutes after starting in the morning, and now it happens always, so in that respect you could say it’s worse, but in some aspects better, because now they can’t say the fault doesn’t occur.
I’ll also do these Scan Pro measurements again. The warranty is still for a year, so there’s still some time.
 
Last edited:
Lambda voltage 1 before cat.: V Lambda voltage 1 after cat.: 0.012 V Lambda sensor 1 integrator: 1.00000 Lambda sensor 2 integrator: 1.00000 Pre-cat lambda state: Open loop Lambda state after cat: Open loop Expected idle speed: 750 rpm
MES 2.7R1 does not measure the lambda sensor before the catalytic converter...
 

Attachments

  • G1.jpg
    G1.jpg
    101.7 KB · Views: 72
Last edited:
And you don’t happen to know what ECU ISO code 7A 07 CE 8C B0 is in my engine, which MES doesn’t recognize (cracked version doesn’t either, but at least it goes further and measures parameters). Strange that they didn’t add it to the program, since I know it’s also present in cars from 2013.
 
ECU ISO code: 7A 07 CE 8C B0 FIAT drawing number: 51969923 Hardware number: MM8GMK HW651 Hardware version: 00 Software number: K410OC48 Software version: 0000 Homologation number: 8GMKF2 Functioning time (EEPROM): 14474 Operating time: 14517 WARNING: Invalid ISO code for selected vehicle system!
... this is a facelift ECU (from 2013), not yet added to MES, AlfaOBD probably doesn’t have it either... however Scan XL Pro reads parameters without a problem, because it only reads PIDs, not directly from the ECU... I would read the topics by bubu321 (.. diagnosing MA 170), there is a program for reading monitors, the status of these monitors will tell you whether the catalytic converter and lambda sensors are good...
 
Last edited:
Logs from today.
Where the arrow points there is an engine jerk and a drop in RPMs - this happens right after selecting first gear, releasing the clutch and during smooth acceleration.
Additionally, 'measured torque' has the same drop, while the expected torque is consistent. Is there something to latch onto here - I mean especially this difference in torques? Alternatively which parameters would be good to measure in such a situation?

After a few minutes it didn’t occur anymore and the charts proceed without drops, and the torques are equal.


185410-logi_z_mes_prosba_o_analize-mes.jpg
 

Attachments

  • mes.jpg
    mes.jpg
    30.7 KB · Views: 126
Last edited:
- And where are those logs from today?

p.s.
- are you thinking about the Scan XL Pro program, you have activation codes on the forum, just get it working.
 
Last edited:
I have ScanXLPro, only I can measure in the dark. I found the codes on some Fiat forum and it works.
Logs, I meant a picture, because in the logs themselves nothing interesting there.

View attachment 2015-12-08.1.zip - at 363 seconds there is no jerk.

Edit: I measured Short Trim and Long Trim.

Short: min -10%, max 21%
Long: min -5%, max 14 %
 
Last edited:
Today I also noticed this. In the parameter description it says it's the voltage on the ECU. So either the sensor is faulty, or the program/interface measures it wrongly (but in other people's logs I found on the forum it's around 14V), or there really is such a voltage, which is doubtful.

READING PARAMETERS:
Battery voltage: 0.48 V
Odometer: 7500.0 km
Odometer reading at last programming: 0.0 km
Number of times engine RPMs exceeded max: 0
Time at max RPM: 0.00 s
Max engine RPM: 0 rpm
Number of re-saves: 1
Vehicle speed (CAN): 0.0 km/h
Engine RPM: 0 rpm
Coolant temperature: 38 °C
Intake air temperature: 31 °C
Engine oil temperature: °C
Ignition timing advance: 0.000 °
Calculated advance angle: 0.000 °
Injector opening time: 0.000 ms
Injector time correction: 3.540 ms
Spark coil charging time 1: 0.000 ms
Spark coil charging time 2: 0.000 ms
Spark coil charging time 3: 0.000 ms
Spark coil charging time 4: 0.000 ms
Knock sensor: 0.000 mV
Engine torque (measured): 0.00 Nm
Engine torque (expected): 0.00 Nm
Air flow: 0.00 Kg/h
Manifold absolute pressure: 1003 mBar
Expected intake pressure: 1000 mBar
Measured boost pressure: 998 mBar
Expected boost pressure: 998 mBar
Boost pressure (sensor): V
Throttle angle: 6.63 °
Throttle angle: 2.0 %
Throttle position (path 1): 6.63 °
Throttle position (path 2): 6.50 °
Throttle plate opening: 50.0 %
Throttle adaptation: Not required
Throttle adaptation phase: Learned
Electronic throttle (emergency mode): Active
Lambda sensor voltage 1 before cat.: V
Lambda sensor voltage 1 after cat.: 0.051 V
Lambda sensor 1 integrator: 1.00000
Lambda sensor 2 integrator: 1.00000
Lambda sensor before cat.: Open loop
Lambda sensor after cat.: Open loop
Expected idle speed: 1120 rpm
UniAir dispersion compensation enabled:
UniAir actuator status:
UniAir solenoid control mode: Late opening
Crank angle of solenoids (command 1): 0.00 °
Adapted VVT position (1): 0.00 °
Adapted VVT position (2): 0.00 °
Adapted VVT position (3): 0.00 °
Adapted VVT position (4): 0.00 °
Adapted VVT position (5): 0.00 °
Adapted VVT position (6): 0.00 °
EVAP valve opening: 0.0 %
Accelerator pedal position: 0.00 %
Accelerator pedal position (sensor): 0.980 V
Accelerator pedal position 2 (sensor): 1.000 V
Clutch pedal switch: Released
Clutch pedal extended: Released
Brake pedal position: Released
Brake stop lamp switch: Off
STOP&START function: OFF
STOP&START request: OFF
Pneumatic brake boost sensor: Closed
Cruise control button - on/off: OFF
Cruise control set (+): OFF
Cruise control set (-): OFF
Cruise control resume (RCL): Released
Expected cruise speed: 0 km/h
AC request: OFF
Compressor: ON
AC pressure: 0.018 Bar
Fan speed: OFF
Atmospheric pressure: 1002 mBar
Universal code: Not enabled
Engine starting: Allowed
Ignition switch position: Run
Automatic transmission: Manual
Current gear: None/neutral
Malfunction indicator: Flashing
Engine performance limiting function: Not active
 
Last edited:
- those readings are strange.
- readings should be taken with the engine running (idle RPM), and with it stopped, as shown below.
READING PARAMETERS:
Battery voltage: 14.24 V
Odometer: 17645.0 km
Odometer reading at last programming: 12450.0 km
Number of times engine RPMs exceeded max: 0
Time at max RPM: 0.00 s
Max engine RPM: 0 rpm
Number of re-saves: 1
Vehicle speed (CAN): 0.0 km/h
Engine RPM: 750 rpm
Coolant temperature: 92 °C
Intake air temperature: 42 °C
Engine oil temperature: 92 °C
---------------------------
READING PARAMETERS:
Battery voltage: 12.09 V
Odometer: 17645.0 km
Odometer reading at last programming: 12450.0 km
Number of times engine RPMs exceeded max: 0
Time at max RPM: 0.00 s
Max engine RPM: 0 rpm
Number of re-saves: 1
Vehicle speed (CAN): 0.0 km/h
Engine RPM: 0 rpm
Coolant temperature: 16 °C
Intake air temperature: 13 °C
Engine oil temperature: 18 °C
- and how about the condition of the monitors, with Scan XL Pro?
 

Attachments

  • G-monitory.jpg
    G-monitory.jpg
    56.5 KB · Views: 46
Last edited:
Here you go:

In the morning, with a cold engine and ignition on (I also noticed that there is no oil temperature measurement. Additionally, in the morning the intake air temperature is always 2-3 C higher than the thermometer in the car and the exterior thermometer at home):

READING PARAMETERS:
Battery voltage: 0.47 V
Odometer: 7514.0 km
Odometer reading at last programming: 0.0 km
Number of overrev events: 0
Overrev time counter: 0.00 s
Max engine RPM: 0 rpm
Number of re-calls: 1
Vehicle speed (CAN): 0.0 km/h
Engine RPM: 0 rpm
Water temperature: 7 °C
Air temperature: 8 °C
Engine oil temperature: °C
Ignition timing advance: 0.000 °
Computed advance angle: 0.000 °
Injection time: 0.000 ms
Injection time correction: 3.540 ms
Coil charging time 1: 0.000 ms
Coil charging time 2: 0.000 ms
Coil charging time 3: 0.000 ms
Coil charging time 4: 0.000 ms
Knock sensor: 0.000 mV
Engine torque (measured): 0.00 Nm
Engine torque (expected): 0.00 Nm
Mass air flow: 0.00 Kg/h
Boost pressure: 1006 mBar
Expected intake air pressure: 1005 mBar
Measured boost pressure: 1003 mBar
Expected boost pressure: 1005 mBar
Boost pressure (sensor): V
Throttle angle: 6.50 °
Throttle angle: 2.6 %
Throttle position (path 1): 6.50 °
Throttle position (path 2): 6.44 °
Throttler valve stalk: 50.0 %
Throttle adaptation: Not required
Throttle adaptation phase: Acquired
Electronic throttle (fail-safe mode): Active
Lambda sensor voltage before cat.: V
Lambda sensor voltage after cat.: 0.047 V
Lambda sensor 1 integrator: 1.00000
Lambda sensor integrator 2: 1.00000
Lambda before cat. state: Open loop
Lambda after cat. state: Open loop
Idle speed expected: 1200 rpm
UniAir dispersion adjustment enabled:
UniAir displacement actuator state:
UniAir valve control mode: Late opening
Intake camshaft closed angle (command 1): 0.00 °
Adapted VVT position (1): 0.00 °
Adapted VVT position (2): 0.00 °
Adapted VVT position (3): 0.00 °
Adapted VVT position (4): 0.00 °
Adapted VVT position (5): 0.00 °
Adapted VVT position (6): 0.00 °
EVAP valve opening: 0.0 %
Accelerator pedal position: 0.00 %
Accelerator pedal position (sensor): 0.969 V
Accelerator pedal position 2 (sensor): 0.992 V
Clutch pedal contact: Released
Clutch pedal extended: Released
Brake pedal position: Released
Brake light switch: Released
STOP & START function: OFF
STOP & START function request: OFF
Pneumatic brake booster shut-off valve: Closed
Cruise control button - on/off: OFF
Cruise control button - accelerate (+): OFF
Cruise control button - decelerate (-): OFF
Cruise control button - resume (RCL): Released
Cruise control target speed: 0 km/h
AC request: OFF
Air conditioner compressor: ON
AC pressure: 0.014 Bar
Fan speed: OFF
Atmospheric pressure: 1007 mBar
Universal code: Not connected
Engine start: Allowed
Key position: ON
Automatic transmission: Manual
Gear engaged: None/neutral
Check engine light: Blinking
Power limit function: Not active


After driving 10 kilometers, idling:

READING PARAMETERS:
Battery voltage: 0.55 V
Odometer: 7525.0 km
Odometer reading at last programming: 0.0 km
Number of overrev events: 0
Overrev time counter: 0.00 s
Max engine RPM: 0 rpm
Number of re-calls: 1
Vehicle speed (CAN): 0.0 km/h
Engine RPM: 853 rpm
Water temperature: 77 °C
Air temperature: 24 °C
Engine oil temperature: °C
Ignition timing advance: -0.125 °
Computed advance angle: 0.500 °
Injection time: 2.038 ms
Injection time correction: 0.582 ms
Coil charging time 1: 3.102 ms
Coil charging time 2: 3.092 ms
Coil charging time 3: 3.174 ms
Coil charging time 4: 3.144 ms
Knock sensor: 209.875 mV
Engine torque (measured): 24.00 Nm
Engine torque (expected): 24.25 Nm
Mass air flow: 9.00 Kg/h
Boost pressure: 713 mBar
Expected intake air pressure: 715 mBar
Measured boost pressure: 996 mBar
Expected boost pressure: 1001 mBar
Boost pressure (sensor): V
Throttle angle: 4.00 °
Throttle angle: 1.0 %
Throttle position (path 1): 4.00 °
Throttle position (path 2): 3.69 °
Throttler valve stalk: 43.4 %
Throttle adaptation: Not required
Throttle adaptation phase: Acquired
Electronic throttle (fail-safe mode): Active
Lambda before cat. voltage: V
Lambda after cat. voltage: 0.176 V
Lambda sensor 1 integrator: 1.10696
Lambda sensor integrator 2: 1.00000
Lambda before cat. state: Closed loop
Lambda after cat. state: Open loop
Idle speed expected: 765 rpm
UniAir dispersion adjustment enabled:
UniAir displacement actuator state:
UniAir valve control mode: Late opening
Throttle closed angle (command 1): 574.81 °
Adapted VVT position (1): 106.75 °
Adapted VVT position (2): 232.06 °
Adapted VVT position (3): 286.31 °
Adapted VVT position (4): 412.69 °
Adapted VVT position (5): 466.50 °
Adapted VVT position (6): 642.25 °
EVAP valve opening: 0.0 %
Accelerator pedal position: 0.00 %
Accelerator pedal position (sensor): 0.977 V
Accelerator pedal position 2 (sensor): 0.992 V
Clutch pedal contact: Released
Clutch pedal extended: Released
Brake pedal position: Released
Brake light switch: Released
STOP & START: OFF
STOP & START request: OFF
Pneumatic brake booster shut-off valve: Closed
Cruise control button - on/off: OFF
Cruise control button - accelerate (+): OFF
Cruise control button - decelerate (-): OFF
Cruise control button - resume (RCL): Released
Cruise control target speed: 0 km/h
AC request: OFF
Air conditioner compressor: ON
AC pressure: 0.030 Bar
Fan speed: OFF
Atmospheric pressure: 1003 mBar
Universal code: Not connected
Engine start: Allowed
Key position: ON
Automatic transmission: Manual
Gear engaged: None/neutral
Check engine light: Blinking
Power limit function: Not active


ScanXL Pro: - lack of measurement is probably the ISO non-compliance issue of this MES version with your engine model (MY 2014, I think)
- I don’t have this information about the brake assist sensor.

185568-logi_z_mes_prosba_o_analize-scanxl.jpg
 

Attachments

  • ScanXL.jpg
    ScanXL.jpg
    40.1 KB · Views: 66
Last edited:
STOP&START function: OFF.
STOP function request: OFF.

Pneumatic brake booster shut-off valve: Closed
Cruise control button - on/off: OFF.
Cruise control button - accelerate (+): OFF.

And that one in red from Scan XL? Is there something to criticize?
 
Amortyzatory
Back
Top