• Jeśli chcesz dodać swojej Alfie charakteru i jednocześnie zaznaczyć przynależność do naszej społeczności – to dobry moment, żeby je zamówić.

    Ramki Alfaholicy

    Szczegóły, zdjęcia oraz informacje o zamówieniu znajdziesz tutaj.

    Nie czekaj, bo jak zwykle schodzą szybko.

Headlight washers

prezes-tk

Active
Joined
Nov 5, 2008
Messages
1,443
Location
Siemianice/Słupsk
Car
Były: 2 x AR 166 2,4 20v, AR 156 1,9 JTD, AR 159 SW 2,4 20v, Giulia Super 2.0T. Obecnie inna marka.
I've been looking since yesterday evening but I couldn't find anything on the forum that could help me. For obvious reasons I’ve been driving less lately, so probably that's why I didn’t notice earlier that my headlight washers aren’t working. I checked in all positions of the light switch, even though I know they should operate when the lights are on, at least dipped beam. But they don’t work. I can’t even say since when. Are they in any way dependent on, for example, a proxy done after the last visit to the dealership (radio was replaced)? I haven’t yet hooked up with MES to check what it shows. But maybe someone has had a similar occurrence.
 
I've been looking since yesterday evening but I couldn't find anything on the forum that could help me. For obvious reasons I’ve been driving less lately, so probably that's why I didn’t notice earlier that my headlight washers aren’t working. I checked in all positions of the light switch, even though I know they should operate when the lights are on, at least dipped beam. But they don’t work. I can’t even say since when. Are they in any way dependent on, for example, a proxy done after the last visit to the dealership (radio was replaced)? I haven’t yet hooked up with MES to check what it shows. But maybe someone has had a similar occurrence.

In MES -> Body -> Tests there is an option to test the washers; besides that, in the fuse box on the right side under the hood there is a fuse (F89) and a relay (T17), I assume you have enough fluid so the indicator doesn’t light up.
 
Last edited:
the washers don’t work also when the level is below the sensor, and as far as I’m concerned they work once in every roughly 10 uses
 
I haven’t connected with MES because I left the laptop at work, but today, when leaving the garage, I tried again and what happened? They spray. On the second try they don’t. Then, after some time, they work again. Do they have any algorithm based on amount or time? Over the last hour I’ve gone through all the manuals I downloaded long ago – none mention how the headlight washers operate. There’s only how to activate them and that they won’t work if the display shows a message about too low fluid level in the reservoir.
 
there is an algorithm, I didn’t check, the every 10x ones I kind of remember from forum or Facebook
 
if you have the ignition on and the lights on, they spray on the first shot – then again after the 10th use of the windshield washers.
 
Confirmed, with the lights on the headlight washers operate on every 10th activation. You can close the topic. But I didn’t find this in the manuals.
 
Stelvio 2021 USA with modified washers. Does anyone know why this isn’t working?

Fuse box:
Zdjęcie WhatsApp 2024-08-06 o 22.15.44_7982ffa1.jpg
I think everything is there?

Power cable to fuse box - socket - 6 wires so the pins should all be there.

MES Test:
Zdjęcie WhatsApp 2024-08-06 o 22.18.27_21c0eaee.jpg

MES settings:
Zdjęcie WhatsApp 2024-08-06 o 22.20.23_ebca10b6.jpg
 
Stelvio 2021 USA with fake sprayers. Does anyone know why it doesn’t work?

Fuse box:
View attachment 289950
I think everything is there?

Fuse box cable - socket - 6 wires so the pins are all there.

MES test:
View attachment 289951

MES settings:
View attachment 289952

you dump the proxy and we have to count which byte and check? you set bit 2 of byte 59, if you did that then the proxy is settled.
As for the rest of the electrical, maybe missing connections from the fuse box to the BCM. as for the completeness of the fuse box at a glance I won’t comment, those 2 or 3 customers I once did activation for, they got schematics and were supposed to check if it’s complete, I know they fabricated some connection(s) and one of them replaced the fuse box with a complete one.
 
byte 59, what should the correct value be?
View attachment 289975

you’re right, bit 2 is set. Is the level sensor connected to K027? is it T17/F89? are there connections from the fuse box in the left behind-the-dashboard area to the BCM for controlling T17? I’m attaching Giulietta schematics.
sprysk_giulia.jpg
wycieraczki_giulia.jpg
in stelvio probably the same though colors may differ.
BTW the washer is only on the first time (and I think every 10th) after turning the ignition on and only when lights are on.
 
Thanks for the schematic.
T17/F89 is the 30A in the photo and the large relay in the photo, they are there; from photos of others I’ve noticed there are also other smaller fuses, hence I wondered if it’s really complete, 30A for the pump is quite a lot.
The sensor is there, it’s on the common connector, the tank-fuse box wire is complete, it has 6 wires, I didn’t check the fuse box-BCM, you’re surprising me a bit with the information that there might be a situation where the fuse box is properly powered, wires to the tank connector are complete but missing wires to the BCM.
I’m wondering if the pump/sensor/locked sprayer nozzles aren’t damaged - could be signaled as a fault in MES as open circuit / short?

Does anyone have a description of the fuse box intended for all elements and the pinout schematic of the tank pump with two pumps?
 
there are no good reverse-side descriptions - pins of connectors generally aren’t mapped, and the drawn fuses, etc., I don’t recall from any eLearns.
Yes, dedicated harnesses are made, more so as the model is on the market longer – there will be several types usually with some extras for common options, but not everything. normal.
If you wonder whether something is damaged, maybe it’s worth checking by connecting your external power? After all you have in the schematic the numbers of the plug pins for the intermediary connector, and already at the pump you probably don’t need schematics? Start by checking the connections to the BCM (D header pins 50 and 60), that’s easy to inspect by looking if a cable exits from socket D in the BCM - socket D you marked which one it is (in stelvio colors often differ, and there are also errors in schematics here though probably not because people built according to these schematics)

I don’t know if there are errors such as a short (then the fuse F31 blows) or an open circuit.

Do the full job and then write, because you’re writing while you go so you’re unnecessarily wasting someone’s (and your own) time.
 
Amortyzatory
Back
Top