• Jeśli chcesz dodać swojej Alfie charakteru i jednocześnie zaznaczyć przynależność do naszej społeczności – to dobry moment, żeby je zamówić.

    Ramki Alfaholicy

    Szczegóły, zdjęcia oraz informacje o zamówieniu znajdziesz tutaj.

    Nie czekaj, bo jak zwykle schodzą szybko.

DNA Sensor, check engine

nataliam

New
Joined
May 14, 2013
Messages
15
Car
xxx
Hello everyone,
I have a question about my problem - maybe you can help me solve it, because the dealer has failed three times already.
In my car, a check engine error (+ engine light) appeared some time ago, and Dynamic and Start&Stop don’t work. At the first visit the dealer wiped the error from the computer, I was supposed to see how it would go. The error appeared again - they changed the oil, because allegedly the computer indicated heavy wear. Additionally, the DPF burned out. It was okay, but after a while the problem returned. My third visit to the dealer resulted in another diagnosed problem and here they traced a damaged/dirty D.N.A sensor. They cleaned it and recommended replacing it if the error pops up again. Some time there was peace and then the same again.. I’m reluctant to replace this sensor, I don’t fully trust the dealers at the dealership since they can’t accurately locate the source of the problem. Has anyone here encountered a similar situation or has any idea what ails my bella? Maybe it is really that D.N.A sensor - if so, does anyone know its location in the car?
Regards! Mito The check engine error appeared some time ago (+ engine light), and Dynamic and Start&Stop do not work. At the first visit the dealer cleared the error from the computer, I was supposed to see how it would go. The error appeared again - they changed the oil because allegedly the computer indicated heavy wear. Additionally, the DPF was burnt out. It was okay, but after a while the problem returned. My third visit to the dealer resulted in another diagnosed problem and here they located a damaged/dirty D.N.A sensor. They cleaned it and recommended replacing it if the error pops up again. Some time there was peace and then the same again.. I’m hesitant to replace this sensor, I don’t trust the dealership technicians completely, since they can’t pinpoint the exact source of the problem. Has anyone of you encountered a similar situation or has any idea what plagues my car? Maybe it is indeed this D.N.A sensor - if so, does anyone know its location in the car?
Cheers!
 
There is no such sensor in the car. what are your symptoms before the light comes on and after.
If you’re from Piekary Śląskie I can read your MITO.
 
Last edited:
check engine error

Hello everyone,
I have a question about my problem - maybe you can help me solve it, because the dealer has failed three times already.
In my Mito The check engine error appeared some time ago (+ engine light), and Dynamic and Start&Stop do not work. At the first visit the dealer cleared the error from the computer, I was supposed to see how it would go. The error appeared again - they changed the oil because allegedly the computer indicated heavy wear. Additionally, the DPF burned out. It was okay, but after a while the problem returned. My third visit to the dealer resulted in another diagnosed problem and here they located a damaged/dirty D.N.A sensor. They cleaned it and recommended replacing it if the error pops up again. Some time there was peace and then the same again.. I’m hesitant to replace this sensor, I don’t trust the dealership technicians completely, since they can’t pinpoint the exact source of the problem. Has anyone of you encountered a similar situation or has any idea what plagues my bella? Maybe it is indeed this D.N.A sensor - if so, does anyone know its location in the car?
Cheers!

I had exactly the same fault in the Fiat Bravo II, it started last winter - turned out the battery was delivering too low voltage - needed charging - check if that helps. Regards
 
Hello,
I have the same fault in MiTo 1.3 jtdm, battery charging didn’t help.
Did anyone manage to solve this problem? additionally on the dashboard there is a crossed-out "S" inside a circle.

Regards
 
Lack of proper charging of the battery is surely not the only reason for the start&stop failure. Personally I had a sequence: check engine > start&stop failure > DNA disconnect. The cause was a vacuum sensor, but it didn’t show up immediately, only after strong pressing of the accelerator during driving. Apparently the computer remembered some vacuum settings and did not alert until I drastically changed engine revs. Start&stop needs a ton of data to function (including accelerator pedal position sensor, clutch, neutral position sensor, battery charging sensor, etc). Missing any of them disables the feature. Also I don’t know, but could excessively low battery voltage cause only the message 'start&stop is unavailable'? Without the yellow icon on the display?
 
- with small daily mileage I get the message "start&stop is unavailable".
- every 3 months I charge the battery and that keeps me calm for 2-3 weeks.
 
Hi, I have a similar problem in my Julka 1.6 jtd, the check engine appeared, Start Stop didn’t work and DNA, at the dealer they read the error "D.N.A.", cleared it and told me to drive on, after about 1000 km the check lights again (the same symptoms), after a few minutes the error disappears (it happened twice).
Any ideas?
 
C1459 Adaptive Mode Switch Circuit Failure

I have a similar problem, the Check Engine light comes on and DNA and Start&Stop turn off, the battery is not 99% because I replaced it a few months ago. No other symptoms, at least I don’t hear or feel anything. The light sometimes goes out, happens randomly, the car can drive 100 km without the light coming on, and other times it lights up after starting the engine.

When connected to the computer at a quick check at the mechanic it shows: C1459 Adaptive Mode Switch Circuit Failure and nothing else.

Does anyone know what this could mean?

Car like in my description - Giulietta 1.6 JTDM, 105 HP 2010
 
The workshop said they give up. Does anyone have an idea what to do? Eventually I’ll go to Carserwis but I’m afraid it will end like: Sorry, we don’t know what happened, we’ll charge 300 zł for an opinion, goodbye.
 
I’ve had the same problem for some time in my Mito 1.4 16v MultiAir. First, a message appeared about StartStop being unavailable, then a Check Engine message and DNA stopped working. However, I noticed a certain weather-related pattern. When it’s cold and humid, these things happen. When it’s warmer, the problems disappear... From what I’ve read, I didn’t find a single concrete solution to this problem. Am I wrong?
 
I have exactly the same question, except it’s for a Giulietta.

I’ve just had a diagnosis at Carserwis (3 hours of work), so it’s unlikely to be just a bulb swap.
The lever position sensor needs replacing (sometimes only for configuration, but not in my case).
 
Ok, so as I understand it, the sensor configuration is the very “adaptation” mentioned earlier? Can this be done via a computer or do you have to disassemble something?
 
Ok, so as I understand it, the sensor configuration is the very “adaptation” mentioned earlier? Can this be done via a computer or do you have to disassemble something?

As far as I know, if you don’t have to replace it, you don’t have to unscrew/disassemble anything.

- - - Updated - - -

Ok, so as I understand it, the sensor configuration is the very “adaptation” mentioned earlier? Can this be done via a computer or do you have to disassemble something?


And the cost of the operation is 1200 PLN (230 PLN for diagnosis, about 300 PLN for the part, and the rest is labor)
 
1200 is the cost of replacing the sensor with a new one, but only after the adaptation via computer doesn’t work?

I’m asking because the service doesn’t know what’s going on and I think I’ll have to take it to some Alfa service in Kraków.
 
neutral gear position sensor. It gives the signal of the so-called slack, i.e., the neutral position.
It is located under the shift lever. Reach it from underneath after removing the thermal cover and the shift lever housing.
First, calibrate the sensor to the neutral position on the attached ignition key with the engine off and the clutch depressed.
If that doesn’t work, replace it.
The sensor is the same across the FCA group :)

thought for reading :)
http://motofocus.pl/technika/9756/b...zez-czujnik-pozycji-neutralnej-w-fiacie-doblo
 
Sorry for dredging up an old thread, but I don’t want to start a new one.
Does anyone know what symbol the neutral gear position sensor for the 1.6 MJTD Julka has?
I can’t find it anywhere.
 
Amortyzatory
Back
Top