• Jeśli chcesz dodać swojej Alfie charakteru i jednocześnie zaznaczyć przynależność do naszej społeczności – to dobry moment, żeby je zamówić.

    Ramki Alfaholicy

    Szczegóły, zdjęcia oraz informacje o zamówieniu znajdziesz tutaj.

    Nie czekaj, bo jak zwykle schodzą szybko.

Damaged throttle

bugaj_90

New
Joined
Jul 1, 2011
Messages
157
Location
Jaworzno (SJ)
Car
Była156 1.6ts Grigio Chiaro. Byla 159 SW 1.9jtdm Bianco Pastello. Byla 156 1.8ts SW. Jest 147 2.0ts
Hi...

Last week I got the check engine light and the car lost some power (it didn’t enter service mode) and the technician said it was an EGR problem, and today I found a moment to take it apart and clean it. While I was at it I thought I’d see how dirty the throttle body is... I unscrewed the pipe connecting the intercooler to the throttle body and horror struck... No "flap" but more importantly there are no screws by which that "flap" is fastened.

Has anyone encountered such a fault?
What exactly does the throttle body do in a JTDm?
Somewhere I read that it’s only for engine shutoff, is that true?

attachment.php

Tomorrow I’m going to dismantle the intake manifold to locate the flap... and, worse, the screws...
 

Attachments

  • CAM00710.jpg
    CAM00710.jpg
    97.4 KB · Views: 2,265
Oh crap... This is basically an shutoff flap rather than a throttle body. Was it there before at all? I’m not completely sure, but this flap probably can’t be pulled out without lifting the pin that holds it. That’s 100% how it is in petrol engines’ throttles in several ARs. In JTDm I haven’t dismantled this flap. The flap should be visible if it really came off. If the screws have fallen further, they may have lodged in the sludge that fills the intake manifold. If they flew into the cylinders, that’s not good...
 
Last edited:
Oh crap... This is basically an shutoff flap rather than a throttle body. Was it there before at all? I’m not completely sure, but this flap probably can’t be pulled out without lifting the pin that holds it. That’s 100% how it is in petrol engine throttles in several ARs. In JTDm I haven’t dismantled this flap. The flap should be visible if it really came off. If the screws really flew further, they may have lodged in the sludge filling the manifold. If they flew into the cylinders, that’s not good...

I pulled it out, and after removing the screws, this whole circular plate just slides out, so there are two options:

1. Some hack removed it because in Vag cars that’s how it’s done...
2. The screws unscrewed and the flap fell in. The problem won’t be the flap itself, but the screws; hope they stuck somewhere to this "dirt" inside the manifold.

Before you start disassembling the manifold, read the manual, there’s a topic I authored somewhere on the forum.
 
After a few hours of struggle, a weight was lifted from my chest. Let me explain why... because in the manifold there was no flap, meaning someone had removed it earlier... just why? since the mechanism works correctly...
The swirl flaps were also removed by the previous owner... for what and why? in general the swirl flap system works only when flaps are removed... what effect did someone aim to achieve with such modifications?

The problem with the EGR valve also became clear: the solenoid works but the valve sticks in the open position and doesn’t close... a cleaning moment and it runs like new.
As for starting and stopping the car, it starts perfectly and when shutting down sometimes it shudders...

There’s an oil leak from under the head toward the timing area, not huge but probably tomorrow the head will come off... I need to sleep on it. Has anyone done a head gasket job on a jtdm? what costs to expect?
 
Head overhaul planned from 400 plus gaskets.. and why swirl flaps were removed you have plenty of topics on the forum :)
in short so you don’t do a engine overhaul if the cylinders swallow them. ..
 
He surely read that you have to remove some flaps and went overboard not to risk.. good he didn’t throw the fuel filler flap in :)
 
What kind of heresy am I reading here?

Why remove the shutoff flap? Probably only to have the engine shake on shutdown and wear the engine mount. NO SENSE!
 
I also keep wondering why someone removed it since the mechanism works...
 
I also keep wondering why someone removed it since the mechanism works...
not because the flap is removed due to mechanism fault, the mechanism can work until the end and the flaps will hit your pistons, and then it’s not funny anymore
 
I understand about the flaps but I mean the shutoff flap...
 
Are you sure this throttle body is only a shutoff flap?
I recently got a fault in the throttle actuator. I removed the throttle body and in its electronics there were oil traces. It went to regeneration. It was sealed (an O-ring on the shaft bearing, factory it doesn’t have) and the electronic board was replaced.
Improvement in engine smoothness is significant. The engine runs less nervously, more like, I’d say, silky responding to the gas pedal. Surely the throttle body works only during engine start/shutdown?
 
Last edited:
Are you sure the throttle body only works during engine start/shutdown?
The throttle body changes the degree of opening during engine operation. Therefore it’s not a "regular" shutoff flap :)
 
The throttle body changes the degree of opening during engine operation. Therefore it’s not a "regular" shutoff flap :)
That’s what I thought too, hence my post.
Labeling it as a regular shutoff flap misleads. Several people after replacing or regenerating the throttle body note an improvement in the engine’s working etiquette and performance.
bugaj_90
So look for a complete throttle body or return yours for regeneration.
What you have won’t provide correct engine operation.
 
Last edited:
Throttle in a CR diesel? There is no such thing. The idle engine is over-fueled and nothing happens because of that.

In my opinion the shutoff flap problem is that the electronics, which are flooded with oil, don’t hold the flap open during operation. Either the flap doesn’t open all the way. But that’s just my intuition.
 
And we have two schools.
Some claim here in Jahu and Belfer that it is only a shutoff flap, i.e., a zero-one system.
Run—throttle open 100%
Off—ignition off—throttle closed.
Another view, like mine and magil, that it probably isn’t like that. That the opening angle of the throttle changes during engine operation.
Is the throttle opening angle parameter visible in FES, for example?
That would be easy to check.
I had the throttle body opened and that sun on the board in the electronics looked like it was collecting data across the full range of operation, not just at open/closed.
 
Last edited:
One of the main functions of the throttle plate besides working with the EGR valve is also to prevent engine hiccups when turning off the engine
The idea is that under certain operating conditions, the throttle creates a pressure difference between the intake and exhaust systems, and that difference is necessary for correct exhaust gas recirculation.
In other words, the throttle controls the amount of air entering the cylinders.
As you know, a diesel engine has a high compression ratio and high pressure of the incoming air in the cylinders, which causes a rough stop when shutting down the engine (turning off)
When the ignition is turned off, the throttling plate stops the air supply to the engine
Because of the reduced amount of compressed air, the engine stops more gently.
 
Regarding shutdown, there’s no room for dispute.
But is the air amount controlled also during engine operation, or only during shutdown?
Is preventing engine shudder during shutoff the only function of the throttle?
 
Amortyzatory
Back
Top