• Jeśli chcesz dodać swojej Alfie charakteru i jednocześnie zaznaczyć przynależność do naszej społeczności – to dobry moment, żeby je zamówić.

    Ramki Alfaholicy

    Szczegóły, zdjęcia oraz informacje o zamówieniu znajdziesz tutaj.

    Nie czekaj, bo jak zwykle schodzą szybko.

BLUE&ME replacement

ads

New
Joined
Oct 27, 2016
Messages
8
Car
Alfa Romeo Giulietta 1.4 TB 120
Hello everyone. Could someone help with replacing the B&M module in Giulietta.
I have a damaged one. I found a suitable used one (eperfiat).
I’d like to know how to remove it and whether a connection to the computer is needed during the replacement, or if just plugging it in is enough and it will work?
Thank you very much for any info.
 
What symptoms of B&M module failure do you have?

The odometer needle is flashing, the steering wheel buttons don’t respond, USB in the glove compartment doesn’t work. The B&M simply won’t start. I was at a service; they couldn’t connect to the module (it lights red on the scan tool). It worked fine before. It failed strangely, i.e., exactly when I plugged my iPhone into the car charger—but apparently that’s a coincidence.
 
Removing the negative battery terminal for a minute helped and the B&M came to life.
 
Removing the negative battery terminal for a minute helped and the B&M came to life.

Didn’t help. I tried. Although later I heard from a service tech (Volvo) that I shouldn’t have even tried such things.
 
Maybe I’ll ask differently. Is there anyone around (up to 150 km) from Nowy Sącz who would take on replacing a used BLUE&ME module?
 
Hello,

I have the same problem with Blue&Me. The same symptoms, the B&M completely disappeared and the odometer is flashing. Could someone suggest how to solve the problem.
Where is the module located, and how to access it?
After replacing the module with a used one (Allegro), is adaptation necessary?
I’ve already tried disconnecting and reconnecting the battery, charging it. Nothing helped.
 
Help, guys. I removed the old module, connected the new one, and turned the ignition. Nothing is flashing, it connected to the phone without pairing. It imported contacts but when attempting to dial a number on the car display it says calling, but nothing happens on the phone. After a few seconds of trying to dial, a message pops up that the phone is disconnected and the B&M disconnects, and it happens every time. Is this a sign of missing pairing, or is the new module also faulty?
Best regards
 
On the next startup, however, the odometer began flashing and pairing was required. The phone connects and even makes calls, but similarly to my previous module, there is a phenomenon that suddenly during a call I hear a tremendously loud squeal, I can’t disconnect the call from the steering wheel, and if I disconnect on the phone, the car still insists I’m on a call and the only solution is to turn off the ignition; sometimes even after restarting the car, the B&M still says I’m on a call. The module I installed up to the last moment worked in the previous Alfa and I’m starting to wonder if perhaps it’s not the module’s fault but something else? Any ideas? Thanks in advance
 
I answer myself here because maybe someone will find this useful in the future.

I replaced the blue&me module with another one, 100% functional, and the same problem persists: after a few minutes (sometimes earlier, sometimes later) the connection with the phone is interrupted and a loud squeal follows, causing a state of pre-heart attack. After digging through the Internet it turned out that it is a very common problem among iPhones, after updating to iOS 11 (roughly 2017) the issue began to appear massively for everyone with blue&me. It is known that there will be no updates beyond 5.6, so it seems the problem is unsolvable for iPhone users; to confirm this, today I will test some other phone.
 
I answer myself here because maybe someone will find this useful in the future.

I replaced the blue&me module with another one, 100% functional, and the same problem persists: after a few minutes (sometimes earlier, sometimes later) the connection with the phone is interrupted and a loud squeal follows, causing a state of pre-heart attack. After digging through the Internet it turned out that this is a very common problem among iPhones, after updating to iOS11 (about 2017) the problem began to occur massively for everyone with blue&me. It’s known that there won’t be updates beyond 5.6, so it seems the problem is unsolvable for iPhone users; to confirm this, today I will test some other phone.

I’ve been using iPhone 7 for about four years now, the same device updated through all versions from iOS 11 to iOS 15. No problems with blue&me.
 
Thanks for the info, in that case this lead is also incorrect, keep looking for the cause.
 
Hi,
Unfortunately I also have the same symptoms with a faulty blue/Me for a long time, the odometer flashes and the buttons on the steering wheel don’t respond ������.
Question: would simply realigning the proxy help?
I intend to finally take this to an electronics repairman, because what annoys me most is the flashing odometer.

- - - Updated - - -
 
Julka imported, repaired, but.... the odometer’s flashing and the steering wheel buttons don’t all work. I read up, went to an electrician—he immediately said that the proxy alignment (proxix adaptation) must be done. He did it, cleared the faults. The odometer is fine, but not all steering wheel buttons work. You can press them, but you can’t increase the volume; station change works, mute works. Phone functions don’t work.
Could these buttons be the cause?
 
Last edited:
They could, but there could also be a wrong button type set (there were several versions - depending on equipment) and through diagnostics you can set the mode.
Although it’s odd that the volume correction would work only partially.
 
Hi, for a long time my Blue&Me module hasn’t been working. The ASO service center stated the module is damaged. I removed the old module. My goal is to be able to play music via USB port (e.g., from a USB drive). I think I have at least 3 options:
- Buy a new module with the risk that it will suffer the same fate as the old module
- Replace the whole radio, which has a USB socket / possibility to connect USB (any suggestions?)
- Add to the current radio a module that enables playing music from a separate USB port (e.g., a separate USB port in the glove box—don’t know how I’d connect to the current USB port in the glove box (from what I understand reading the forum, the USB port is normally linked to the radio via the blue&Me module).

Anyone know anything concrete?

PS I have Multiecuscan, so theoretically I can do proxy alignment / change some settings in the configuration
 
Last edited:
My Blue&Me module just failed too and here are the conclusions so far:

New ones aren’t available (ASO says they no longer produce them (sic!)).

Used ones are very hard to come by (I didn’t find a matching one, they only appear in archives).

Disabling the odometer blinking reportedly requires intervention in the body computer (per Kocar).

I’ll try to send the module for repair to revtronic (can’t add a link, they’re on eBay) (I didn’t find a company in Poland, but on eBay there are companies from Italy, for example).
 
New ones aren’t available (ASO says they no longer produce them (sic!)).
I’ll try to send the module for repair to revtronic (can’t add a link, they’re on eBay) (I didn’t find a company in Poland, but on eBay there are companies from Italy, for example).
Thanks, let me know if the repair succeeded.
I got info from a service in Szczecin that there is no known delivery date, and the cost is over 2000 zł.
Could someone suggest other alternatives - I want to listen to music from a Pendrive, but over 2500 zł with labor seems quite steep.
Anyone recommend something proven?
 
Regarding replacing the blue&me module, the truth is that usually they are interchangeable if they’re from a similar production period. I saw in mito a module plugged in from a Fiat Punto two years ago and it works great to this day, there was a similar thread on the forum
 
Amortyzatory
Back
Top