• Jeśli chcesz dodać swojej Alfie charakteru i jednocześnie zaznaczyć przynależność do naszej społeczności – to dobry moment, żeby je zamówić.

    Ramki Alfaholicy

    Szczegóły, zdjęcia oraz informacje o zamówieniu znajdziesz tutaj.

    Nie czekaj, bo jak zwykle schodzą szybko.

Blade installation

moosiak

New
Joined
Apr 27, 2015
Messages
253
Location
Wrocław
Car
Giulia
I have just completed the blade installation in my non-blade Giulietta.
Brief description.
To install the blades you need the blade module, sold on Allegro together with turn signal/wiper stalks and the lower steering column cover.
136C61E5-F9F5-46F0-ADF3-E059C99A1663.jpg
At this moment, a description of just the exchange without activation. I did the replacement together with a friend mechanic based on a description from an Italian forum.
1. Removing the Airbag - locate the opening from under the steering wheel, insert a flathead screwdriver and, despite resistance, push it vertically upward.
2. Disconnecting the Airbag - two plugs, requiring dexterity and nimble fingers. Before disconnecting I disconnected the battery, this is associated with several errors that disappeared after a drive and restarting the car. (Esc off)
307AE52C-8FF6-4A64-BF87-8D4D565BA98D.jpg
3. Disconnecting the steering wheel plugs and the replaced module
B59E16B0-0450-4FBE-9EC1-25CA3F6F35BD.jpg
4. Unscrewing the steering wheel - spline with a guiding groove. Alfa marked the center point on the thread and the steering wheel.
5. Unscrewing the screws of the lower steering column cover. Two Torx screws.
6. Removing the module - 4 screws - two from the front, two from above. The upper and lower covers are snap-fitted at 6 points, separate with some force.
7. Disconnecting the module - 4 plugs to disconnect.
8. Locating the 5th plug on the harness. In my case it was taped over with adhesive tape.
1AC1C7AB-3BA1-49D1-8C5C-96A88B27ECBF.jpg
9. Installing the new module with the new plug connected.
10. Putting everything back together.
776DD644-BA5C-4FCA-A9C5-E922B1A6C656.jpg
 
Last edited:
I already had the lane-keeping assistant, and the steering wheel heating. Everything still works. The blades will be activated tomorrow.
Module supporting these functions - 156125194
Lower cover part number - 156110210
 
So not every blade fits? I also have both heating and the assistant.
 
Could you elaborate on the steering wheel and blade heating?
For the blades you need a lower cover, because versions without blades don’t have the required openings.
What’s up with these numbers?

Is heated steering wheel standard and does it require decoding?

Moosiak, thanks for starting such a great topic. I’ve seen several nice cars in stock, but none had blades, which for me are mandatory in Giulias.
 
Bez tytułu.jpg
Everything is possible. The loom is run everywhere the same (according to Eper).
However, the modules differ:
Bez tytułu.jpg
Bez tytułu.jpg
and for heating a switch on the central console and a steering wheel with heating (NHS) are needed
 
Last edited:
the switch under the steering wheel is specific to heating the steering wheel ( NHS ), the stalks can be added to any switch
 
Hi. I’m planning to replace the small display to 8.8 but it’s hard to find more info on how to do the replacement.
 
If we’re talking about that beeping for lane keeping, I don’t see it in Proxy.

But this lane-keeping assistant can be enabled and disabled in the menu or on the turn signal stalk, but they want to add parking assist, which isn’t in Gulli/Stelvio even in the options :)
 
moosiak, well done and enjoy the blades - I love them. And it’s nice you shared knowledge, for me important info that MES is already tested in Proxi for Giulias.
Screenshots you posted from the mobile version, did you do Proxi on it? I know you used MES from kozak -a, I thought he had a PC version?
 
moosiak, well done and enjoy the blades - I love them. And it’s nice you shared knowledge, for me important info that MES is already tested in Proxi for Giulias.
Screenshots you posted from the mobile version, did you do Proxi on it? I know you used MES from kozak -a, I thought he had a PC version?
PC version

Sent from my HMA-L29 using Tapatalka
 
On my phone I just checked what and how in simulation mode. PC activation in 10 minutes.
OK. regarding Proxi I’ve done a bit retrofit work but only on 159/Giuliettas, I was curious if MES is refined enough to work OK. On my current version, firstly I can’t just run Proxi (I have SGW, I would have to bypass, but I’m not sure it’s good to do Proxi without the current module especially and then add it later - would the car treat it as a configuration change?), and secondly some modules still show MES as Unknown ISO code on connection - supposedly it opens for them after confirmation, supposedly reads parameters, but I would prefer to have a clean setup before Proxi - would give hope they tested more, e.g., Proxi.
 
Amortyzatory
Back
Top