• Jeśli chcesz dodać swojej Alfie charakteru i jednocześnie zaznaczyć przynależność do naszej społeczności – to dobry moment, żeby je zamówić.

    Ramki Alfaholicy

    Szczegóły, zdjęcia oraz informacje o zamówieniu znajdziesz tutaj.

    Nie czekaj, bo jak zwykle schodzą szybko.

Antenna replacement.

axion80

New
Joined
Nov 12, 2013
Messages
61
Location
Gdynia
Car
Giulietta 1.4 MA 170 KM TCT
Has anyone ever replaced the antenna (not just the base)? I need information on how to do it.
 
Has anyone ever replaced the antenna (not just the base)? I need information on how to do it.

The roof antenna is usually attached with a screw through which the cable runs, and all of this is in the headliner space. I did it on a Golf V but I think the principle is similar. So access is probably from the rear - by tilting the headliner. You will surely need to remove the rear pillar trims and perhaps also the plastic handles by the headliner - those above the rear doors. But it depends on how far you have to lower the headliner. From what I saw in EPER, the rear pillars have clips and one screw. In the Golf the screw was under the airbag cover; in the Julia there seems to be some decorative cap - I suspect the screw is under it. Then there is the removal of the rear light in the headliner - in EPER I don’t see screws, so it might be held with clips along with the headliner. So maybe after removing or tilting the pillar trims, pull the whole rear of the headliner down to release it from the clips and that’s it. If anyone did it in a Julia, please share more ;)
 
I am also interested, specifically what diameter the hole in the roof for the antenna has. The version without NAVI and with a sunroof that opens - if that matters. I’m considering installing another antenna myself — Sirio Triflex - three-band antenna - CB, FM, GSM — I just worry that it will cover the factory opening.
 
Has anyone ever replaced the antenna (not just the base)? I need information on how to do it.

Didn't you think about having someone who "knows" do it? I did it at an A.S.O. the antenna was 100 PLN (whole, not just the base) and labor also around 100. I was afraid of pulling on the headliner.
 
and did you remove the ceiling light... maybe that’s enough...???
That’s enough. Remove two upholstery mounting pegs, take out the light, and there is access, a bit tight but doable. Behind the light there is the antenna cable connector. Beware of the glass residue, I recommend doing it with gloves—at least those from a gas station.
 
I remember doing it on a 147.. pulling the headliner always carries the risk of it bending... and that looks very bad later..
 
You buy the cheapest flat wrench 22, on one side 5 cm from the end you bend it at 45 degrees and unscrew the antenna - then you don’t have to bend the headliner much (I pressed anti-swish foam blocks on both sides of the opening so you don’t pull in one spot). I’ve dismantled the antenna about 4 times just through the lamp opening and there are no upholstery creases if you do it sensibly
 
You buy the cheapest flat wrench 22, on one side 5 cm from the end you bend it at 45 degrees and unscrew the antenna - then you don’t have to bend the headliner much (I pressed foil-wrapped foam on both sides of the opening so you don’t pull in one place). I’ve removed the antenna about 4 times only through the lamp opening and there are no creases in the upholstery if you do it carefully
do you think such a wrench would fit, or would it be too short for the bend?
https://allegro.pl/klucz-plasko-oczkowy-lamany-z-grzechotka-22mm-vr-i7272229643.html
 
I think it’ll work for bending, just that it probably won’t turn well there because that part will probably drop down due to its own weight - so maybe it’s better to use something more durable there
 
Last edited:
I was thinking about that too, but I’m afraid that if I bend the wrench I’ll probably snap it rather than bend it. How did you do it? In a vice? Did you heat the wrench so it would be a bit more flexible or not?
 
I was thinking about that too, but I’m afraid that if I bend the wrench I’ll probably snap it rather than bend it. How did you do it? In a vice? Did you heat the wrench so it would be a bit more flexible or not?
In its jaws ;) seriously though I think in a vice it was long ago and I barely remember but it can definitely be bent - I bought some cheapest one at a hardware store from some junky material exactly for that, so it would be thin and soft :-)
 
Why bend wrenches, when the whole operation can be done normally, without gimmicks, with a regular wrench. A bit of feel and patience - nothing will break. My headliner didn’t suffer.
 
And on a different note, can the amplifier in the base be diagnosed somehow or is it only by replacement? Because the weather isn’t inviting for such fun and my garage is cold [emoji16]
 
ant.jpg

Two days ago the radio stopped working, a puddle appeared yesterday. Tomorrow I’ll pick up the antenna from the ASO.
 
Sorry for posting after another post.

I took it apart yesterday, the board was slightly damp, but no deposits, scale. I dried it, plugged it in quickly, it sounded like new. I took it apart, sealed the critical points, works great.

I’m getting in the car in the morning, a problem.

I already have a new one bought, but I’m wondering why it doesn’t work, since the board wasn’t killed for good.
 
the fact that you can’t see anything doesn’t mean electronics isn’t damaged. There’s also the issue of the blade contact strip to the radio core - it may not be making proper contact; it’s good to clean the contacts properly with some spray and slightly bend that strip
 
Explain one thing to me. The amplifier is being replaced and it is in that rectangular enclosure, right? Because I wanted to buy that module but I see some people list exactly this rectangular one, and others say that the amplifier is in the base of the antenna hidden, and I’m confused :/
 
Amortyzatory
Back
Top