• Jeśli chcesz dodać swojej Alfie charakteru i jednocześnie zaznaczyć przynależność do naszej społeczności – to dobry moment, żeby je zamówić.

    Ramki Alfaholicy

    Szczegóły, zdjęcia oraz informacje o zamówieniu znajdziesz tutaj.

    Nie czekaj, bo jak zwykle schodzą szybko.

Start & Stop

piotr_c

New
Joined
Jun 15, 2009
Messages
539
Location
Rzeszów
Car
Stelvio & Stelvio
Hi,

listen, how do I disable this for good? - when I turn it off with the button from the console, after a while it activates by itself anyway :mad:

I want to disable it for good!



Merry Christmas
 
Unfortunately, with every engine restart the S&S activates again, and you have to turn it off again. There is no other option. Unless maybe it can be completely disabled through the FES.
 
Or a straightforward electronic circuit that short-circuits the contacts for a moment after power is supplied.
 
This S&S is getting on my nerves... In the new FES — I’ll add that with it being registered (3.5) there is nothing like that...
 
Sure, especially when I braked quite hard before an intersection and right after braking S&S turned off the engine — thanks, I want to disable it in the heck
Ecology: EGRs, DPFs, S&S and other tricks ;)
 
Just hold the clutch during unplanned stops :) that's how I do it when I have an unplanned stop at a red light and earlier I was pressing hard ;) and generally I disable that device when I’m driving in the evening, somehow due to the xenon lights. And during the day I manage the system :)
 
That doesn’t bother me at all. I’ve gotten used to it from the start. And when stopped first at lights it’s enough to keep it on the clutch and first gear
 
So here's the thing: the only option is to flash a new calibration to the car, that’s quite professional, and less professional you could look around the gear lever area; there must be a gear lever position sensor, i.e., what position it is in. If you unplug the plug or something, S&S will surely not work, but what consequences that will bring you’ll have to investigate yourself :P
 
So here's the thing: the only option is to flash a new calibration to the car, that's quite professional, and less professional you could look around the gear lever area; there must be a gear lever position sensor, i.e., in which position it is. If you disconnect the connector or something, S&S will surely not operate, but what consequences that will have you’ll have to figure out yourself :P
Flashing a calibration, is that a mod of the software via OBD2?
 
No software, nor other fiddles, just disconnect the linkage from the gear-shift position sensor (linkage, not the plug, or it will throw an error!!!). The electronics will think it’s in gear and the engine won’t stall. That’s the whole philosophy of S&S, beer and help for me :)
 
As long as the gear-in-use is detected at the lever and not somewhere in the gearbox like a reverse light switch. Besides, isn’t that signal possibly used somewhere else. Keeping the clutch engaged is not very convenient and I’m not sure how it is in modern cars, but in old times it heavily shortened the throw-out bearing life (now probably such issues don’t exist but who knows). I still prefer wiring in the system. A ridiculously simple operation—after turning the key, short a micro-relay that we connect to the two wires going to the switch. Also for amateurish fast driving, if we use two relays we can automatically enable the D mode. I myself wired in an Atmel-based module enabling changing the wiper interval (disliked the factory action) and there were plenty of programmable outputs, but for that purpose some simple two-transistor, a few capacitors, resistors, and a micro-relay patent will suffice. On the other hand, doing this in a single unit will probably be a pain.
 
You went for it :P It seems the guy knows the subject better :) I just, in my own line of thinking, suggested without ever looking at how it works, let someone figure out these sensors and let us know how it went :)
 
Why all these combinations, relays, switches and other fiddles? Just unplug the linkage and problem solved. This sensor is solely for S&S, so there’s no problem that something else won’t work :) I know what I’m writing about, tested in many Alfas.
 
Refreshing the Start&Stop topic a bit. After a short drive, a yellow Start&Stop indicator lights up along with a warning triangle, and the screen shows the message “Start&Stop unavailable.” What is the cause? Where is the aforementioned gear lever position sensor and its connector located, as mentioned in earlier posts?
 
Amortyzatory
Back
Top