Program Scan XL Pro in diagnostics.
- the Scanxl Pro program supports the ELM327 interface.
- because a minimum of 12 parameters are displayed on the screen, the interface used must be fairly fast.
- this criterion is met, for example, by the OBD Link-SX interface with its COM speed at 115200 baud.
- the program does not work with ELM 327 clones and not only due to their slow speed of 38400 baud.
- the program creates *.lgf log file, *.VDl table configuration file, *.cfg general configuration file
- as well as the *.vrt file, a template of a virtual chart.
- the table in the program can consist of several templates of virtual charts.
- a virtual chart template can contain from 2 to 8 charts.
- usually good readability is provided by a virtual template with 4 charts and a table with 3 virtual templates.
1. after installing the program and connecting, we select Settings | PID Configuration | Manufacturer | Check correctness
- the program checks how many PIDs are available from the car manufacturer; we can only work on these PIDs. - the ScanXL Pro version 3.5.1 is from 2010, there is no newer version or updates to the program, which is why the program has some shortcomings.
- therefore it is good to download the OBD Auto Doctor program and see in the Extras tab how many PIDs our car really has.
[zdjecie 18004.jpg]
- the ScanXL Pro version 3.5.1 is from 2010, there is no newer version or updates to the program, which is why the program has certain limitations.
- therefore it is good to download the OBD Auto Doctor program and check in Extras how many PIDs our car really has.
[obd auto doctor.jpg]
2. next, you should record (red button or F3) a few frames so that the program enters the data, we stop with the red square and
save the current log.
- this step is not always necessary, surely when the program displays data that there is no PID.
3. select Diagnostics | Data View (previously selected) [18026.jpg]
4. then Tables Resolutions | Charts or select Load dashboard layout (*.vdl),
the program will load a table with 3 templates of measured parameters. [18010.jpg]
5. for configuring individual templates go to Settings [18012.jpg]
in Settings of the Table | General Information you can select individual PIDs and mark that these charts should be active.
in Settings of the Table | Axis Information we set minimum and maximum of the measured range (0 - 8000 for SAE-RPM)
we can also save the table separately as a virtual chart template (*.vrt) [18016.jpg]
6. we can monitor data in real time (F2 monitor) [18033.jpg] time axis green or immediately save
data from the car (F3) time axis red [18032.jpg]
stop monitoring or save with the F4 key, red square.
7. remember to save the log file (*.lgf) right after recording [18018.jpg]
8. before closing the program it is good to save the program configuration, File | Save Configuration as (*.cfg) [18020.jpg]
9. loading a saved log file, Load from File [18023.jpg]
after loading the log file we can replay recorded data with the Play button (green).
10. the current read position is indicated by a white, vertical line; stop chart with F4 key (red square [18024.jpg])
11. after loading another log file we can see what data was recorded, Diagnostics | Data View
based on these data we can prepare new tables if needed [18025.jpg].
- the Scanxl Pro program supports the ELM327 interface.
- because a minimum of 12 parameters are displayed on the screen, the interface used must be fairly fast.
- this criterion is met, for example, by the OBD Link-SX interface with its COM speed at 115200 baud.
- the program does not work with ELM 327 clones and not only due to their slow speed of 38400 baud.
- the program creates *.lgf log file, *.VDl table configuration file, *.cfg general configuration file
- as well as the *.vrt file, a template of a virtual chart.
- the table in the program can consist of several templates of virtual charts.
- a virtual chart template can contain from 2 to 8 charts.
- usually good readability is provided by a virtual template with 4 charts and a table with 3 virtual templates.
1. after installing the program and connecting, we select Settings | PID Configuration | Manufacturer | Check correctness
- the program checks how many PIDs are available from the car manufacturer; we can only work on these PIDs. - the ScanXL Pro version 3.5.1 is from 2010, there is no newer version or updates to the program, which is why the program has some shortcomings.
- therefore it is good to download the OBD Auto Doctor program and see in the Extras tab how many PIDs our car really has.
[zdjecie 18004.jpg]
- the ScanXL Pro version 3.5.1 is from 2010, there is no newer version or updates to the program, which is why the program has certain limitations.
- therefore it is good to download the OBD Auto Doctor program and check in Extras how many PIDs our car really has.
[obd auto doctor.jpg]
2. next, you should record (red button or F3) a few frames so that the program enters the data, we stop with the red square and
save the current log.
- this step is not always necessary, surely when the program displays data that there is no PID.
3. select Diagnostics | Data View (previously selected) [18026.jpg]
4. then Tables Resolutions | Charts or select Load dashboard layout (*.vdl),
the program will load a table with 3 templates of measured parameters. [18010.jpg]
5. for configuring individual templates go to Settings [18012.jpg]
in Settings of the Table | General Information you can select individual PIDs and mark that these charts should be active.
in Settings of the Table | Axis Information we set minimum and maximum of the measured range (0 - 8000 for SAE-RPM)
we can also save the table separately as a virtual chart template (*.vrt) [18016.jpg]
6. we can monitor data in real time (F2 monitor) [18033.jpg] time axis green or immediately save
data from the car (F3) time axis red [18032.jpg]
stop monitoring or save with the F4 key, red square.
7. remember to save the log file (*.lgf) right after recording [18018.jpg]
8. before closing the program it is good to save the program configuration, File | Save Configuration as (*.cfg) [18020.jpg]
9. loading a saved log file, Load from File [18023.jpg]
after loading the log file we can replay recorded data with the Play button (green).
10. the current read position is indicated by a white, vertical line; stop chart with F4 key (red square [18024.jpg])
11. after loading another log file we can see what data was recorded, Diagnostics | Data View
based on these data we can prepare new tables if needed [18025.jpg].
Attachments
Last edited:
