• Jeśli chcesz dodać swojej Alfie charakteru i jednocześnie zaznaczyć przynależność do naszej społeczności – to dobry moment, żeby je zamówić.

    Ramki Alfaholicy

    Szczegóły, zdjęcia oraz informacje o zamówieniu znajdziesz tutaj.

    Nie czekaj, bo jak zwykle schodzą szybko.

Problems with MA

Capricorn

New
Joined
Nov 1, 2014
Messages
2
Car
AR Mito QV
Hello,
I have a question for everyone who has previously encountered problems with the MA module. In my MITO 1.4 (170) year 2010 (imported) for some time now the CHECK ENGINE error appears, it comes and goes, sometimes longer, sometimes shorter, with no pattern. Last week I went to the authorized service for diagnosing what could be the cause of such behavior. I received a printout from Examinera and a printout of the Central Unit Test. On the first one the following information appears: P1064 - signal of the UNIAir solenoid activation Cyl.4 Mechanical damage; the actuator is locked. In the central unit test printout, several potential causes are also given: from high wiring impedance through oxidized contacts at the solenoid, excessive fluctuations in battery voltage, presence of air bubbles in the oil, incorrect oil level, high switching resistance of the UNIAir solenoid, a damaged UNIAir solenoid up to a damaged injector control unit. After everything, the shift supervisor verbally informed me that the cause could also be a dirty engine oil with metal shavings, for example. At the ASO the errors were reset, and I immediately replaced the oil outside the ASO with MOBIL 0W-40 ESP (it was the same Mobil before). Unfortunately after one day from MiTo the check engine light came on again. After reading a few posts I conclude that I do not feel any particular difference in engine operation, yet my wife, who uses the car daily,
stated that every time the CHECK ENGINE light comes on, the car seems to shake a little.
Given that the replacement module costs are known (around 3500.00), I have the following question: I am looking for a reliable expert (region Mikołów-Katowice-Tychy- Gliwice) who can diagnose which of the above causes of the fault activation is the correct one and whether the ASO suggestion to replace the entire module was justified.
 
problem with P1064.

Hi there. Still having a problem with the fault? I had the same and I think I dealt with it.
 
Hi there. Still having a problem with the fault? I had the same and I think I dealt with it.

jedrus33 write how you dealt with it, it will be for posterity. for me the oil change helped for a month (knock on wood) the fault didn’t appear, oil standard Selenia.
 
Fortunately I had a friend in the service who had a bit of a brain. I had an identical diagnosis, module to replace but he told me that sometimes immediate oil change or cleaning of such an oil screen that gets clogged helps. He said this screen should be cleaned every two oil changes, and generally no service does this, or doesn’t know, or doesn’t care. Better to sell a new MA module. The screen is located under the timing cover, exactly I don’t remember, but something like that. It must be unscrewed with an ampoule and thoroughly washed. My mechanic did this for me and since then it’s like magic. If nothing physically happens to the car and only this fault pops up, there’s a good chance it’s due to contamination. After cleaning I’ve been driving for 4 months and the fault never appeared. My oil was about 7 thousand [kilometers] and also Selenia.
 
In July of this year I was asking here on the forum about repairing the multiair module. Now I’ll describe the whole history: My sister with her husband bought a Alfa Romeo Giulietta 1.4 170 MA. The car was bought in Germany, the ad stated that the multiair module is broken. The price was correspondingly lower and attractive enough that they decided to buy it. At first I tried to dissuade them from buying this version of the Giulietta altogether, proposing a different, less problematic 120 HP one. I said you’re buying a pig in a poke, because it’s unknown what stage of failure the module has reached. It seemed the engine ran loudly and the check engine light was on. But they insisted, because the price was low and a friend in Germany had the tow truck, so they brought the Alfa right away. Already in Poland it turned out that the engine not only runs abnormally but started to smoke white. Since I thought it was unnecessarily restarted, since it was already known the module is broken.
Alfa It waited quite long for repair, because my brother-in-law insisted on a workshop of his choice. The mechanic started work and diagnosed a turbocharger failure and one injector. In the turbine there were small metal pieces that spread through the engine. And the injector was jammed again. In my opinion this is worn bushings from multiair. I know that the cylinders were honed and piston rings were replaced. So the pistons were probably the same? The turbine was rebuilt and the engine assembled and started. When I asked why the mechanic started a freshly rebuilt engine that has a broken multiair, my brother-in-law said the mechanic did not tell him about the multiair failure. His pious wish was that the multiair would turn out to be working. So they bought a new multiair module for 2900 PLN. I ask my brother-in-law: was the car connected to a computer before? Would the mechanic calibrate the module? Will the module be filled with oil? he doesn’t know.
Alfa It ran off after 2 months. The engine has Castrol oil (which I think is awful). I still don’t know if the mechanic applied the full procedure when replacing the multiair. All this reportedly cost about 8 thousand PLN. One year warranty, condition: oil change after 5 thousand km.
Alfa it runs supposedly super. I hope everything will be fine. I was more upset than the car owners.
Giulietta replaced a 147, which sold very quickly. There was talk of a 2010 Alfa with about 125k km. In December last year a thorough service: oil change to 5W30, timing belt replacement. In the service book there are stamps every 30k km. In one place there is a service after 42k km. The first ones were done at the ASO.
 
Last edited:
hey - I read a post from PAni 2016 about the problem with the P1064 error in Multiair engine and check engine - I now have the identical problem with a Fiat Bravo 1.4 MA and they threaten me with replacing the module for 4000 PLN. - someone wrote that cleaning the filter screen after the timing belt helped - would you be so kind and write how it ended for you? - did you replace the module, or did the simpler solution help? - regards - Wojciech Osiński
 
I’ll answer because I also had this problem.
Generally, if MA is not in an imminent failure and errors pop up sporadically, in the first step you should change the oil with a flushing agent and unscrew and clean/replace the screen under the timing cover. It’s really a quick job and a clean conscience...
 
I had a similar problem, error P1062 and the check appeared and disappeared. It appeared on a cold engine after 2-3 km and disappeared in the afternoon. Checked battery, spark plugs, coils. The car was 4 thousand after oil change. Regeneration of MA helped - not a replacement with a new module. (cost-effective option about half price).
 
because MA MUST be filled with oil when COLD, if you start it immediately after fueling, MA will start to fail after some time.
 
Ehhh I’m not that much of a fool. I never start the engine before it reaches operating temperature, especially in Mietek. In my understanding, cold means in the morning, after the night, after a longer stay in the garage, the first start. Sorry for the incorrect term.
 
You know, in normal engines you start and drive, regardless of how long it sat, not counting hard driving.
In MA this behavior is a doorway to failures of that system. Here you start and wait, you wait the longer the colder it is.
The oil also matters, what type is used.
 
Amortyzatory
Back
Top