• Jeśli chcesz dodać swojej Alfie charakteru i jednocześnie zaznaczyć przynależność do naszej społeczności – to dobry moment, żeby je zamówić.

    Ramki Alfaholicy

    Szczegóły, zdjęcia oraz informacje o zamówieniu znajdziesz tutaj.

    Nie czekaj, bo jak zwykle schodzą szybko.

Pre-cat lambda probe - no reading

śnieżix

New
Joined
Feb 13, 2017
Messages
154
Car
Julka TCT
W giulietta 1.4 MA 170 the lambda sensor before the catalytic converter isn’t working for me - in MES it’s simply "V" on its own, there’s no number before it

First I replaced the sensor with a new one - NGK/NTK, nothing changed.

I gave the car to an electrician, he worked on it for a month, returned the engine computer for checks - supposedly OK, he finally said it was fixed.

I picked up the car and nothing changed, the mechanic claims he has a video where it’s recorded that it worked for him. When asked what exactly he repaired, I’m told that he doesn’t know himself, "something with a connector not making contact most likely"

And now the question - has anyone had such a problem? Can anyone recommend an electrician in Łódź who would be able to fix this? I’ve been dealing with the problem for several months
 
Sensor 100% functional?

Why NGK and not Bosch?
 
factory new sensor, original. I feel it’s not a problem of the sensor itself because on the previous BOSCH (original from new) it was exactly the same

NGK because I thought the quality would be good

the whole issue is that the mechanic claims that it worked once, didn’t work once - that’s not a classic sign of a damaged sensor. he gave me the car back with supposedly working sensor, only my MES shows no changes
 
Last edited:
Do you have original software?
Because the ECU should report something.
 
the car has original Magneti Marelli ECU and nothing has been changed in the ECU, it’s 100% factory. interestingly the ECU does not report any errors related to the lambda problem, nothing lights up on the dash either. the car drives normally, and I found out about the problem from the LPG tuner, because I went for LPG tuning, and he said he wouldn’t tune because my lambda isn’t working
 
Hmm

Here in my 1.75 TBi there’s a quirk with the lambda sensor. Under one part number there are two different ones, so it’s 50/50 whether you hit the right one :-). Also, during a replacement, someone at the ASO (I know who, but no names :-)) wondered why there are parts with different parameters and the same part number.

Lambda error in my case triggered the check engine (eco-friendly). Even today I was arranging papers and saw a printout from diagnostics with a note next to the lambda error (that it’s the CE line).
 
For me there’s exactly no check, no errors, the electrician who previously did two cars for me without problems couldn’t handle it, the mechanic also tried before, couldn’t manage. I don’t know whether to take it to the ASO, because ideas are running out
 
Unplug the sensor plug and see if at least 2 errors appear.
 
unfortunately I’m not able to unplug the plug because it’s seated so tightly I don’t know how to disconnect it

I went for a tune/inspection with a mechanic, he claims the sensor works, and that in MES it doesn’t show the sensor voltage before the catalyst (it’s just a V with no value) but that’s fine, because this is a wideband sensor and it won’t show a voltage. And that in another program (Car Scanner connected via OBD wifi) it shows the long-term correction at 83% as a completely constant line which is a problem with that program, not the car (?)

however when switching in MES to the chart "Lambda sensor 1 integrator" the chart comes alive and revolves around 1 and in his view everything is correct

can someone confirm that this is how it should look in MES? the whole fuss about replacing the sensor started after going to the gas installer for tuning, the gas installer didn’t see the corrections and that’s why he said the sensor needs replacement, and as I understand that’s the problem in Giulietta are these corrections simply not easily accessible to view?
 
What LPG installation? With me, on the KME NevoSky Jet OBD the program shows the real Lambda value instead of the sensor voltage because "this is a wideband sensor".
Make sure your gas installer knows Fiat electronics, because some programs can’t read the corrections from them correctly - for example in Torque the correction value (x) is shown as 100%-x, so with a correction (+/-)5% it shows (+/-)95%. The result is that while driving steadily the short-term correction range jumps from -100% to 100% and there’s not much you can read from that.
 
In your engine there is a two-state sensor and not a wideband one.
Connect with the engine but pick, for example, a Fiat or a Lancia
 
I don’t understand any of this anymore. the sensor I have installed is described as a wideband, that is the 5-pin sensor, we’re talking about the sensor before the cat in Alfa Giulietta 1.4 benzine MultiAir 170 HP produced 2011

https://www.amazon.pl/Sonda-lambda-NGK-90532-55214916/dp/B00CJNY5G6
"NGK UAA0001-FA001 wideband sensor"

additionally I found somewhere on a forum a comment from someone who wrote that the lack of reading Lambda1 in MES "is supposed to be like that" - this isn’t my screenshot, just a screenshot of someone with an identical situation as mine:
G1.jpg

is there some list of software that will correctly provide real-time corrections in my car - of course excluding software typically for LPG calibration, because I have a Vialle installation so I won’t use that software, because it seems it doesn’t use OBD but a LPG computer which is Vialle and its software doesn’t provide corrections

The gas installer who originally set it up for me is from Silesia; back then in 2017 he managed fine, but now over the phone he said they tune by corrections and if they don’t have access to the corrections they won’t be able to help me
 
Amortyzatory
Back
Top