• Jeśli chcesz dodać swojej Alfie charakteru i jednocześnie zaznaczyć przynależność do naszej społeczności – to dobry moment, żeby je zamówić.

    Ramki Alfaholicy

    Szczegóły, zdjęcia oraz informacje o zamówieniu znajdziesz tutaj.

    Nie czekaj, bo jak zwykle schodzą szybko.

Mito 155KM Lambda sensor

Joined
Jul 24, 2011
Messages
15
Car
Alfa Romeo 1.4 TB 155KM Rok produkcji 2009
Hello!
Some time ago the check engine light came on. I went to a mechanic to check on the computer what is going on. It showed an error of the lambda sensor, but all indicators were normal. The mechanic of course cleared the error and told me to drive. He said there could be many causes, e.g. poor quality fuel, a hole, or simply city driving, i.e. traffic jams. After 24 hours of use the light came back on. Nothing is wrong with the car. Power is within the norm, engine temperature too. The only thing that doesn’t work is the DNA system. Of course the price of an original sensor is very high, so I checked substitutes. The mechanic recommends only Bosch substitute, although warns that the sensor may also vary... What can you advise me? Cheers Paweł
 
Apparently Mito it has 3 sensors, that's why I wrote that the middle one :) It is near the engine so I assume it is before the catalyst.
 
There can be many causes, faulty mass air flow sensor, worn spark plugs, poor quality fuel, leaky exhaust system, or a worn (contaminated) Lambda sensor. To check it go to a real diagnostic person.
 
Last edited:
Only buy original BOSCH (no universal substitutes) - unless you have a lot of money and want to collect sensors.... By the way, when a fault occurs you replace the damaged component and not just clear it - driving with a damaged one sensor can lead to further engine harness damage
 
I have a similar problem and how did you manage to solve it???? because the mechanic is about to replace half the car and the problem will be the same
 
I have a similar problem and how did you manage to solve it???? because the mechanic is about to replace half the car and the problem will be the same

Change the mechanic since this one can't handle it and is earning at your expense. No one remotely can solve your problem like a GOOD and trusted mechanic can, not a crook who sucks money out of you.
 
- is it so hard to connect, for example, a FES (MES) with a CAN interface e.g. ELM 327 ver 1.4, then after connection press the A (all) key, wait, then the N (neutral) key and from the FES/MES home catalog attach the *.txt file like the one with the measurement date.
- only from that file will we know which sensors it has, whether wideband or narrowband, how many sensors there are, whether they are electrically connected, how many sensors are before the catalyst, how many after the catalyst.
 
mito and I think it has two probes, upstream catalytic converter a universal 5-pin wide-band LSU) and downstream a diagnostic probe 4-pin. this LSU is marked 0 281 004 123, price about PLN 600, mileage 250,000 km, price of the second about PLN 250, mileage 160,000 km ..... unfortunately FES, MES do not provide voltage for this first wide-band probe.... the wide-band probe is detected by the AlfaOBD program... giulietta Lambda 1 signal (Pre-Cat.): V Lambda 1 signal (After-Cat.): 0,199 V Lambda sensor 1 integrator: 0,99097 Lambda sensor 2 integrator: 1,00000 Lambda 1 status (Pre-Cat.): Closed loop Lambda 1 status (After-Cat.): Open loop Idle RPM desired: 765 rpm
- AlfaOBD program shows the current of the wide-band probe but in the current version it does not provide the Lambda or Long, Short parameter.
- attempting to set and force a measurement using the appropriate PID results in an error.
 

Attachments

  • LSU 0281004123.jpg
    LSU 0281004123.jpg
    27.2 KB · Views: 141
  • Sonda-lambda-G940-1-4-TB.jpg
    Sonda-lambda-G940-1-4-TB.jpg
    28.7 KB · Views: 154
Last edited:
Hi.
Are we able to measure afr via obd2 at the moment?
 

Attachments

  • 10010-error na sondach pradowych.jpg
    10010-error na sondach pradowych.jpg
    98.1 KB · Views: 181
Last edited:
And on PC yes?
Klon elm327 is enough?
And torque pro?
Sensor 1 bank 1 gives from 0 to 1V.
In what range does our sensor measure?
Or maybe someone has an afr indicator?
 
I don’t have alfaobd on PC.
In mes we certainly won't read AFR. Voltages you can convert to AFR values. There is even some table online.
 
Question whether this converter is universal.
I arranged a quick diagnostics with Bubu, but I’m looking for a proper interface. A friend has stn1170, but I don’t have access to it right now.
I messed up the gas system with stagmobile and I’m looking for a way to read afr from obd2. After summer we’ll buy stagafr with a friend as a joint thing.
 
Question whether this converter is universal.
I arranged a mini diagnostics with Bubu, but I’m looking for a decent interface. A friend has the STN1170, but I don’t have access to it yet.
I messed up with gas via StagMobile and I’m looking for a way to read AFR from OBD2. After holidays we’ll buy Stag AFR with a friend in a partnership.
 
Amortyzatory
Back
Top