• Jeśli chcesz dodać swojej Alfie charakteru i jednocześnie zaznaczyć przynależność do naszej społeczności – to dobry moment, żeby je zamówić.

    Ramki Alfaholicy

    Szczegóły, zdjęcia oraz informacje o zamówieniu znajdziesz tutaj.

    Nie czekaj, bo jak zwykle schodzą szybko.

Ignition switch!!!

kaarolek1

New
Joined
Dec 21, 2018
Messages
90
Car
Alfa Guilietta 1.4 2014
When turning the key in the ignition, it often locks, i.e. I cannot turn it to start the engine, then I have to repeat the action, switch off, wait a moment, and turn to start again and only then will it allow starting, does anyone have it the same in their car?

Sent from my FIG-LX1 using Tapatalka
 
how does that work exactly, because I found something like that in the manual??
250.jpg
251.jpg


Sent from my FIG-LX1 using Tapatalka
 
Correctly, the ignition should work like this: you turn on the ignition, twist to the start position and release the key. After turning the key to the start position, there is no possibility to twist back into that position. This is a safety feature so you cannot turn the key to the start position while the engine is running, because you would break the starter. You then need to switch off the ignition and turn it on again.
 
I insert the key, turn to the MAR position and wait a moment, then try to start, and either I do it without the slightest problem or the key just doesn’t budge, to be precise you cannot turn it to the right. In this situation turning to the left (start position) and trying to start again helps...

Sent from my FIG-LX1 using Tapatalka
 
Oh dear! maybe the mechanism of the ignition has mechanically failed, right?
 
I insert the key, turn to MAR and wait a moment, then try to start, and either I do it without any problems or the key doesn’t move at all, to be precise you cannot turn it to the right. In this situation turning to the left (start position) and attempting to start again helps...

Sent from my FIG-LX1 using Tapatalka

Maybe you’re turning the key too fast/too hard and the lock engages. Try slower, gentler.
 
For me the issue is that while the engine is running I can pull out the key; sometimes after switching off it doesn’t spring back fully and there’s no lock. I have a TCT.
 
And I have another problem with the ignition or rather the key.
When I turn the key of the type pocket knife (Giulietta from 2011) from MAR to start more and more often the starter does not respond. This happens roughly every 3rd, 4th start. Only after pulling back the key and turning to start again does the car start. Interestingly, recently I use a regular key and not once has the problem occurred. Is it the immobilizer or its interaction with the key?
Does the immobilizer cut the starter? In another car I remember it cut the ignition, and the starter always turned.
Maybe someone had a similar case and solved the problem.
 
The immobilizer does not cut the starter. It cuts the signal to the computer. It does not authorize starting. The car will crank the starter but not start. There’s something wrong with the ignition switch, though it’s strange that on one key it works normally and on another there’s a problem.

Sent from my EML-L29 using Tapatalka
 
Are you sure? 2-3 times I had a similar situation, the starter didn’t turn and the immobilizer indicator lit up. After returning the key and turning again, everything was fine, it started normally.
 
Immobilizer doesn’t cut the starter. It cuts the signal at the computer. It doesn’t grant permission to start. The car will crank the starter but won’t start. Something is wrong with the ignition switch, though it’s strange that on one key it catches normally and on another there’s a problem.

Sent from my EML-L29 using Tapatalka

Thanks for the tip but I think it must be something wrong with the key. If on one key everything works fine, for now I won’t look for the problem in the ignition. But what could be wrong with the key (when it turns normally without any hang-ups) probably only the immobilizer ???
 
Sometimes mine doesn’t crank the starter on the first try, turn it again and it’s OK. Of course I turn it as the instructions say. I’ve already gotten used to it ;)
Maybe something with communication on one of the modules, the computer waits for all reports and one of them is slow?
 
But with one key it doesn’t complain at all, and with the other (the pocketknife key) every third try to start the car it doesn’t turn the starter.
dobryalf maybe try changing the key, maybe you have the same. Earlier I had the problem quite rarely (maybe once a month) now it’s starting to annoy.
 
This isn’t about the battery, because the ignition switch or immobilizer work with the regular key (the one without a battery).

However with me (not sure if a coincidence but after discharging the old battery and changing to a new one) a problem also appeared with the second key.
Maybe try programming the keys again in the body computer? What do you think, will it help? Or is it a problem with the ignition switch.
 
Yes, the battery didn’t help. Replacing the battery is planned because the current one is already borderline. I wonder which one, the ASO suggested Centra (?)
 
If Centra, it’s probably CL600 (EFB battery for start-stop). I have a similar battery to this Exide but with higher capacity because it’s for a diesel. Now Centra/Exide are the same EFB batteries (they even have identical prices)

- - - Updated - - -

But after replacing the battery I still have problems with the ignition switch
 
But with one key it doesn’t complain at all, and with the other (the pocketknife key) every third try to start the car it doesn’t turn the starter.
dobryalf maybe try changing the key, maybe you have the same. Earlier I had the problem quite rarely (maybe once a month) now it’s starting to annoy.

It turns out that with the second key there is also occasional no response to 'turning'. Probably it is the ignition switch after all!
 
Now that it’s a bit cooler and damp, the problem with the ignition switch disappeared (I already had it on every 2-3 attempts to start and waited for it to fail completely :).
Maybe it is the electrical installation problem, perhaps some connectors aren’t connecting. Damage to the ignition switch is unlikely. Does anyone have experience with this problem, maybe suggest what to do. Otherwise I’ll start repairing electrical connections by feel.
There must be something wrong with the electrics in Julki (likely the Alfa Romeo Julki or Jułki? but 'Julkach' seems model-specific slang) because sometimes (depending on weather/humidity) the instrument cluster lighting goes out or partially flashes (part of the tachometer or temperature gauge)
Probably worth starting the search there, maybe there are some critical connectors in Julki that need fixing ???
 
Amortyzatory
Back
Top