• Jeśli chcesz dodać swojej Alfie charakteru i jednocześnie zaznaczyć przynależność do naszej społeczności – to dobry moment, żeby je zamówić.

    Ramki Alfaholicy

    Szczegóły, zdjęcia oraz informacje o zamówieniu znajdziesz tutaj.

    Nie czekaj, bo jak zwykle schodzą szybko.

Front upper strut mount

marekm

Member
Joined
Jul 6, 2006
Messages
442
Location
Kraków
Car
służy do jazdy, a nie do oglądania
Symptoms are "rubbery" clunks when turning the steering wheel at a standstill or at low speed. Does anyone know the original part number? Any proven replacements? Edit: And should I replace both sides (one clunks) at once?
 
Last edited:
I think it’s about the bearing of the MP strut; good replacement prices from 150 to 200 PLN each. BOGE No. 88-784-R, SACHS No. 802 450. Original part no. 51813225
 
Last edited:
Hello,

does this clunk come from a specific side? Could it be that it’s actually the left or right side? On my car something clunks at low speed and at standstill... but only with the engine running. And the sound seems to come from the tie rod or the steering rack rather than from a particular side. Has anyone encountered such symptoms?
 
Unfortunately the problem with this bearing hit me too. At standstill, engine on, when turning the steering left-right you hear clunks. I went to a diagnostician and he confirmed the left bearing needs replacement. You can also check yourself by placing a hand on the shock absorber in the fender and when someone turns the wheel you can feel light jumps. If someone has replaced it, can you write how long the replacement of one side takes? And which parts were used. Can anything sensible be chosen from this? http://www.iparts.pl/auto-czesci/mo...-od-2008-09,1-4-105km,2-7587-3317-100371.html

-
 
There’s quite a lot of work, because you have to tear out the entire McPherson strut. The biggest problem will be the steering knuckle ball joint; if you don’t know how to detach it without damaging its rubber boot, better leave it to professionals...
Already more than one person lost nerves on these ball joints
 
There’s quite a bit of work, because you have to tear out the entire McPherson strut. The biggest problem will be the steering knuckle ball joint; if you don’t know how to detach it without damaging its rubber boot, better leave it to professionals...
Already more than one has lost nerves over these ball joints

What joint?! you unscrew the upper mounting "cap", 2x bolts from the steering knuckle, stabilizer link and that’s probably it. The biggest problem I had was squeezing the weak-quality spring with spring compressors, but somehow it worked. I ordered the bearing + mount here http://motostacja.com/p/1939/23283/...e-i-uklad-kierowniczy-czesci-samochodowe.html

Edit:
These may also be handy, wipers/universal spring compressors.
 
Last edited:
So what?
You had to do it on the car, there’s no force for a complete McPherson to pass under the fender without disconnecting the ball joint from the steering knuckle

- - - Updated - - -

So what?
You had to do it on the car, there’s no force for a complete McPherson to pass under the fender without disconnecting the ball joint from the steering knuckle
 
So I understand that this whole dismantling isn’t that bad when you don’t have to fight with this ball joint. Well then, great, thanks a lot for the info. And that SNR company that colleague kefir sent is decent? Because I thought for such a bearing you had to pay at least 100 PLN. So that after replacement it would last ideally another 80k km. And I still wanted to replace both sides :)
 
Yes, the thing is simple. I suspect that colleague prezes01 meant the Giulietta, hence the tie rod end topic.
In MiTo it looks like this:
- You remove the wipers, a puller may be useful.
- You remove the undertray with 3 screws, a few clips.
- Take a bent 18 mm wrench and an Allen key (5,6?) for the nut and loosen the nut near the plate
- Unclip the brake line, ABS line and the sensor wire for pad wear from the damper so you don’t break anything
- Unbolt the stabilizer link from the damper
- Unscrew the damper/knuckle bolts (2 pcs)
- Unscrew the nut all the way near the plate while holding the damper so it doesn’t fall out
- Take the whole assembly out onto the table (damper, spring, bearing, mount)
- Fight with compressing the spring, the bearing must be loose
- Unscrew the nut and you have the bearing with mount in your hand
- The rest is the reverse :)

- - - Updated - - -

Regarding the quality of SNR I think it’s similar to what you sent. You just chose a rather pricey shop ;]
 
Last edited:
Amortyzatory
Back
Top