• Jeśli chcesz dodać swojej Alfie charakteru i jednocześnie zaznaczyć przynależność do naszej społeczności – to dobry moment, żeby je zamówić.

    Ramki Alfaholicy

    Szczegóły, zdjęcia oraz informacje o zamówieniu znajdziesz tutaj.

    Nie czekaj, bo jak zwykle schodzą szybko.

Errors during PROXI Alignment

Joined
Oct 12, 2020
Messages
5
Car
Alfa Romeo MiTo 2012 1.3 JTDM-2
Hi there!

I’ve only recently become the owner of Alfa Romeo MiTo 1.3 JTDM-2 from 2012.

When buying I didn’t pay attention to the blinking odometer. As I learned later, to get rid of the blinking gauge you need to perform a ‘PROXI Alignment’.

Using Multiecuscan 4.61 software and the appropriate cable I managed to enter the ‘PROXI Alignment’, but the procedure did not end in success.

During the ‘PROXI Alignment’ two errors pop up:

Convergence Telematic Node (CTM) FAILED! - Timeout error
Airbag Node (NAB/ORC) FAILED! - Request out of range error

I’ll add a report from Multiecuscan - While looking for answers on Google I came across a similar thread but didn’t find an answer to my problem.

Has anyone here encountered these errors? Does anyone know what triggers them?

Thanks! View attachment Report1.pdf

While searching for answers on Google I came across a similar thread but didn’t find an answer to my problem.

Does anyone here have these errors? Does anyone know what triggers them?

Thanks!
 
Wrong cable
Set high speed in the Interfaces tab.
If that doesn’t help, you need to buy another interface
 
Wrong cable
Set high speed in the Interfaces tab.
If that doesn’t help, you need to buy another interface

Do you mean a wrong ELM327 cable?
What surprises me is that the other modules flashed through without problems (Body Computer Node (BCM/NBC) SUCCESS! and Dashboard Node (IPC/NQS) SUCCESS!)
I’ll try setting 'high speed' when I get home and let you know!
 
Wrong cable
Set high speed in the Interfaces tab.
If that doesn’t help, you need to buy another interface

I changed the interface to 'High Speed' - unfortunately during the 'PROXI Alignment' the errors still pop up Convergence Telematic Node (CTM) FAILED! - Timeout error and Airbag Node (NAB/ORC) FAILED! - Request out of range error. On the 'Info' screen, in the list of modules 'Convergence Telematic Node (CTM)' is marked in red with a note 'EOL Failed' - PXL_20201013_174814420.jpg

I don’t know if this will help but when entering the computer another error also pops up - B107-4A PROXI configuration control - PXL_20201013_174720626.jpg
 
this info from the rear wiper may indicate even body damage.

The wiper doesn’t return to its place. I’ve seen the same problem on Fiat Punto - I’m planning to simply replace the wiper motor. Unless it’s just some bigger problem I don’t know about...

- - - Updated - - -

Can it be cleared?

Yes, but the wiper error returns every time the ignition is turned. I don’t know what triggers the PROXI error. Can errors in the computer affect performing PROXI Alignment? Even if they have nothing to do with the modules that won’t flash?
 
First repair, then adaptation.
And replacement of the motor without necessity.
Look for a topic about the door lock harness.
 
Error B1074-4A

I'll join the topic
After replacing the radio with a Chinese 2 DIN unit
the odometer pulsates, after studying this type of problem I wanted to perform a PROXI Alignment and in principle it would work but an error B1074-4A appears after clearing and turning the ignition back on the error comes back, after disconnecting the radio it is the same, the odometer lights flicker this one error appears and after clearing it and re-starting the ignition it returns and the odometer still flickers has anyone had a similar problem?
 

Attachments

  • IMG_20220213_094924.jpg
    IMG_20220213_094924.jpg
    58.1 KB · Views: 75
Last edited:
Amortyzatory
Back
Top