• Jeśli chcesz dodać swojej Alfie charakteru i jednocześnie zaznaczyć przynależność do naszej społeczności – to dobry moment, żeby je zamówić.

    Ramki Alfaholicy

    Szczegóły, zdjęcia oraz informacje o zamówieniu znajdziesz tutaj.

    Nie czekaj, bo jak zwykle schodzą szybko.

engine control unit

bubu321

New
Joined
Sep 1, 2007
Messages
6,823
Location
Wrocław
Car
G 1.4 MA 170CV ECU Nexus 8GMF
- in case of absence of CODE card or mismatch between the purchased code and the code programmed into the Engine Control Unit (ECU), we will have to remove the body of the computer.
- after removing the ECU, the next challenge is to disconnect the electronics board from the fuse board.
- the boards are connected to each other without soldering using Tyco Electronics "Board-to-Board" connectors.
- on the electronics board, from the inside, there is a soldered integrated circuit 95C320 that we must read with a programmer.
- after desoldering these boards and desoldering the 95C320 (in an SSOP8 package), we can read the contents of this circuit by any method.
- the screenshots below show that this circuit was re-soldered onto a programmer module for reading.
- after reading the binary contents of the circuit, the CODE value can be read.
- after reassembling the ECU, with AlfaOBD software we can check whether we have the possibility to log into subprograms such as key programming.
- the varying levels of difficulty are visible from the screenshots below.
- a binary file from this ECU is attached; at the end of the binary contents the VIN of this car is written.
 

Attachments

  • BSI-G 004.JPG
    BSI-G 004.JPG
    112.3 KB · Views: 328
  • BSI-G 009.JPG
    BSI-G 009.JPG
    161.3 KB · Views: 483
  • BSI-G 012.JPG
    BSI-G 012.JPG
    127.2 KB · Views: 261
  • BSI-G 015.JPG
    BSI-G 015.JPG
    107.4 KB · Views: 280
  • test-7946-49451.rar
    test-7946-49451.rar
    718 bytes · Views: 80
Last edited:
Curious question - which program did you use to extract the CODE from the memory dump?
 
@bubu321 please describe how to make a key in Mito or a Giulietta, this would be useful too... and why we buy a used key from Allegro and something there to solder. I already found it, we desolder the PCF 7946 IC and in its place solder a new unprogrammed one... and with which program can you re-code the key, and with which program to program the key so that it works in the car immediately... after recoding the key (transponder PCF 7946) you can program the key, e.g., with AlfaOBD software... after programming the key the resulting code, the binary, must be re-uploaded into the ECU body again... am I describing it correctly, I translated it from English, from another forum...
 
- this description is a bit patchy, but the idea is good and effective.
- what matters in every case is the contents of the ECU, where CODE and more importantly the SEED and the keys programmed so far, are stored, lost and abandoned.
 
- the previous method involved removing the ECU from the car, disassembling the ECU into individual boards.
- this method has the drawback that during disassembly something can be permanently damaged.
- therefore I traced the wiring diagram of the 95C320 EEPROM and found test points on the second side of the board; they are usually used during final testing after electronic assembly at the ECU manufacturer.
- perfect for us, the connection diagram is below.
- the M95C320 IC on the printed board has pins 8, 7, 3 permanently connected, so we will only need 6 wires to connect the ECU to the programmer.
- we will use a Reveltronics programmer, it has supply voltages from 1.8 V to +5 V.
--
http://www.reveltronics.com/pl/
--
- after soldering the connections, first connect to the programmer and archive the EEPROM, like two times.
- now compare the read files; if they are the same, we can continue testing this connection.
- in the screenshots below you can see that after erasing the EEPROM, the original value is written back into the ECU body with content verification.
- advantages: we do not have to desolder the EEPROM, we do not have to take the ECU apart.
- drawbacks: we must buy a programmer.
- all these steps are needed to finally reprogram an additional, spare second key for a G.
 

Attachments

  • 95C320-4.jpg
    95C320-4.jpg
    88.5 KB · Views: 200
  • revel-prog-is-0.jpg
    revel-prog-is-0.jpg
    143 KB · Views: 212
  • revel-prog-is-1.jpg
    revel-prog-is-1.jpg
    153.8 KB · Views: 221
  • revel-prog-is-2.jpg
    revel-prog-is-2.jpg
    100.5 KB · Views: 265
Last edited:
The problem is that in case of car theft you will not get money from the insurance due to the extra key created this way. Now the first thing the insurer checks after a theft is whether the original keys you must give them show signs of having extra keys made based on them (which is easily visible under a microscope). If this was done outside the official service, i.e., without re-coding the keys, they assume the owner made a spare key himself and handed the spare to the thief.
http://www.newsweek.pl/wydania/1274/dorobiony-kluczyk-odszkodowania-nie-bedzie,74366,1,1
I have confirmed this with the insurer; it works exactly like that. You can prove your case in court, the question is whether it will be considered and whether the time to end the proceedings is worth the savings on making a spare key outside the official service.
 
- an interesting opinion in the discussion, worth considering before spending 950 zł on a new key from the official service.
- I once visited a "key makers" market; they and the thieves do not need your spare key.
- they connect via OBD-II cable to their software and perform immobilizer-off on the "living" car.
- then with a universal key they start the car's ignition and the car drives away.
- and you have the original key in your pocket, a service key in the cupboard, the registration document in your pocket and the vehicle card hidden in the cabinet, insurance OC and overpaid comprehensive or you don't have OC.
- keep dreaming of holidays you will go on by car.
- but who steals Alfas with equipment worth 50,000 zł, that is the question?
 
- an interesting voice in the discussion, worth considering before spending 950 PLN on a new key from the dealership.
- I once went to a "key makers" fair, they and thieves don’t need your assembled key.
- they connect via an OBD-II cable with their software and do an immobilizer-off on the "live".
- then with a universal key they start the car’s ignition and the car drives away.
- and you have the original key in your pocket, a service key in the cabinet, the registration document in your pocket and the vehicle card hidden in the drawer, insurance OC and overpaid AC or you don’t have AC.
- keep sleeping and dream about vacations you’ll take with the car.
- only those with equipment costing 50,000 PLN steal Alfas, that is the question?

No, I know that a thief doesn’t need a key, at least a professional one :) What I mean, however, is that making a key outside the official dealer network for no reason you pay for the option of “theft” in your insurance, because you won’t get compensation for it.

And regarding the price for duplicating a key - if it really is 950 PLN that is banditry. In SEAT I once had a death, and I apparently had the most expensive version, duplicating with programming cost 550 PLN.
 
- after removing the body computer and performing the work they re-mounted the BC in place.
- pressed and corrected all disconnects.
- after this operation they performed error clearing and Proxy Alignment.
- fixing the connections allowed Proxy to connect to the radio, navigation, which previously was not possible.
 

Attachments

  • sa-proxy.jpg
    sa-proxy.jpg
    58.4 KB · Views: 172
I have a question; if I bought a used key with remote from another car, can I code it to mine having the original coding card with the codes and if there is no possibility to code the key, can the remote be matched to the central locking and what would the procedure be?
 
- in G there is a problem of this kind that the chipset embedded in the key is integrated with the remote.
- and besides it is a single-use programming type, only for the original car.
- if you buy a key from another car, you still have to desolder and insert a new chipset.
- then program the key using CODE, the chipset itself programs the remote.
- with keys from Allegro there is a problem of this kind that newer keys have a completely new chipset, which cannot be obtained on the market.
 
these 20-pin chips are not available on the market, a pity because there are quite a lot of such keys for G... P.S.. just today I tried to program an additional key for G, AlfaOBD crashed when entering CODE, didn’t accept a good value.... AlfaOBD version is 1.6.9, so the only option left is reprogramming the body computer?....
 

Attachments

  • key-2 006.JPG
    key-2 006.JPG
    90.8 KB · Views: 126
  • key3-004.jpg
    key3-004.jpg
    82.4 KB · Views: 115
Last edited:
Dear colleagues,
Has anyone had a problem with the rear hatch wiper stopping in uncontrolled positions in Julka?
At the dealer after 2 attempts they stated that the problem lies in the body computer...
Can someone recommend a specialist near Warsaw?

Paweł.
 
Isn’t it the case that with a damaged body computer the odometer flashes? At least that was the hint I got at the dealership. I also have a problem with the rear wiper, though both wiring harnesses were replaced. One of the guys here points to the wiper motor, which after a minor repair restored normal wiper operation. BC is quite costly.
 
Isn’t it the case that with a damaged body computer the odometer flashes? At least that was the hint I got at the dealership. I also have a problem with the rear wiper, though both wiring harnesses were replaced. One of the guys here points to the wiper motor, which after a minor repair restored normal wiper operation. BC is quite costly.

Exactly nothing is flashing.
The electrical harness was replaced and checked again. The small motors and their connections were also checked.
I searched forums in the UK and it ended up with replacing the body computer with identical symptoms.
So before I invest PLN 1500-2000 I’d rather practice the settings in the computer - by someone who deals with this routinely :)

...the rear wiper works, but the program length and parking position are random.
 
Last edited:
On English forums they also suggest that the "trunk opener" can interfere with the rear wiper, especially when it’s wet.
 
Dear colleagues,
Has anyone had a problem with the rear wiper stopping in uncontrolled positions in the rear window in Julka?
At the dealer after 2 attempts they stated that the problem lies in the body computer...
Can someone recommend a specialist near Warsaw?

Paweł.

Hi,
have you somehow solved this problem? For me the front wipers especially when it’s wet behave as they wish, and the rear one occasionally (after wiring repair for quite a while it was okay, but the problem came back).
The odometer does not flash.
What are the exact costs of replacing the BC or can someone repair it?

- - - Updated - - -
bubu321 perhaps you can do something about this BC? How do you remove it from the car?
 
Amortyzatory
Back
Top