• Jeśli chcesz dodać swojej Alfie charakteru i jednocześnie zaznaczyć przynależność do naszej społeczności – to dobry moment, żeby je zamówić.

    Ramki Alfaholicy

    Szczegóły, zdjęcia oraz informacje o zamówieniu znajdziesz tutaj.

    Nie czekaj, bo jak zwykle schodzą szybko.

Adding components (electronics)

bogas

New
Joined
Jul 27, 2010
Messages
382
Location
Jaworzno
Car
MiTo 1,4MATB 135KM
I would like to add a few things to the car, but trying to enable cruise control with Multiecuscan discourages me.
The Italians have Leonardo Accinni, and we’re still waiting. Like in the service manual :(
But if I finally gather myself and install the switch assembly with cruise control, maybe I’ll fit one with auto mode for the wipers and lights, and then add sensors?
What is the code for the rain and dusk sensor? Do I attach it?
I have the same doubts about Blue&Me and the xenon control units.
If anyone has knowledge, please share - what is the current state of the harnesses in the car (cruise control, xenons, Blue&Me, dusk and rain sensors) and what I should buy for each system.

Additional question - my BC is 50518121. If I buy 505084590, will it facilitate adding the above systems?
How to clone it via OBD2 (immobiliser, alarm)?
 
the Italians also have wiTECH, and it can do everything, it just has to be online with the internet...
what type of ECU is in your car model....
I’ve already found 8GMF, I don’t know what you have for BSI, if Marelli is type 10 then cloning it is no problem.
I won’t answer other questions, I don’t own such a car.
 

Attachments

  • BSI Marelli.jpg
    BSI Marelli.jpg
    49.9 KB · Views: 91
  • ECU-8GMF.jpg
    ECU-8GMF.jpg
    60.2 KB · Views: 106
Last edited:
the body computer is one thing, but the question is whether the wiring harnesses are present in the car for modules that weren’t there from the factory? I don’t think so but maybe I’m wrong and I underestimate the Italians ;)
 
Take this BC?
Can you handle it? For how much? :)
Or I’ll copy via OBD2.
Connect to the BC itself on the table?

- - - Updated - - -

That’s true - the harness for cruise control was reportedly a lottery.

What do I need for each system - B&M, dusk&rain, xenon?
 
wiTech 3000 PLN (or euro, I don’t remember .. but probably zlotys) per year + used device 8-10k ... Shall we pitch in on the forum ? :)
 
... and there will be a small diagnostic equipment rental service at a European level..., I’ve woken up now.....
if there are elements of Magnetti Marelli production in the car then cloning their contents isn’t a problem.... the question is whether this cloning will allow adding new elements..... in Giulietta there are all the cables, connectors, connections, just add the new device, run a CAN scan, correct the BSI content and finally perform a Proxy Alignment.... that’s how it works in this model.....
 
- I haven’t seen an interface for Delphi.... so you still read the BSI on the table, when you are replacing it you still have both on the table.... I would wait a bit more, maybe someone will suggest something about BSI Delphi....
 
in Giulietta there are all the cables, connectors, connections, just add the new device, run a CAN scan, correct the BSI content and finally perform Proxy Alignment.... that’s how it works in this model.....

I wish it were that simple but unfortunately it’s not as you write, I even went to the car to check and it confirms what I wrote before, the wiring in the harnesses is only as much as needed, nothing extra, at least in my Progression from 2010 with Marelli 10 Body :

- wiring for Blue&Me - missing

- wiring for rain sensor - missing

- wiring for cruise control - missing

I didn’t feel like taking it apart any further because it’s a waste of time ....
Even if it were possible to reprogram the computer it doesn’t mean everything will work, because if certain elements are physically not present on the board then how could it work. Differences in BC between various equipment levels are probably not just a matter of software
 
Last edited:
I have a request, could someone write to me (simply, almost in a step-by-step way), how one can add to Mito cruise control (roughly, I won’t be doing this myself anyway)? I would also appreciate approximate costs of such an operation. Regards!
 
Amortyzatory
Back
Top